Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

If you had a big burly maple tree to sell. *LINK*

Posts

If you had a big burly maple tree to sell. *LINK*

#1

If you had a big burly maple tree to sell. *LINK*

Keith Newton----Little Rock, Arkansas

Where is the best place or way to sell to turners? I'm sure lots of you buy your turning blanks, but I have never bought anything but a whole tree.

There is a nice one over on a sawmill site, that I think would be wasted if he tries to turn it into lumber.

It seems like there ought to be a place to post a photo, then have the turners reply right to the sawyer with part of his tree circled, saying send me this part.

Or how would you advise the fellow through this link to cut and sell his tree.


http://www.woodweb.com/cgi-bin/forums/sawdry.pl?rev=680889

Re: If you had a big burly maple tree to sell. *LINK*

#2

Looks more like redbud than maple to me....

Dick Coers

and all the redbud burls I've seen are full of cracks and ants! Still should look pretty.

Re: If you had a big burly maple tree to sell. *LINK*

#3

Re: If you had a big burly maple tree to sell.

Barbara Gill

Keith there are turners who read the site as well as sawyers, including me. I hope he posts a follow-up picture of whatever he finds once the log is opened. You never know if the burls are sound until they are opened.

Re: If you had a big burly maple tree to sell. *LINK*

#4

Re: If you had a big burly maple tree to sell.

Don Evans

This thread brings up a problem I have run into. It seems that everyone who saws wood with turners in mind NEVER think of "hollow forms". Am I just looking in the wrong spots?

It seems the big name turners put out amazing stuff but where are they getting the wood? Are all of them buying whole logs?

All I seem to find is bowl blanks, I've even tried to get one individual who handles wood sales to get me half logs but it never seems to happen. No money restrictions have been placed on it so I just don't understand.

Where does Mahoney get wood for his hollow forms for example?

Or Drozda for her signature pieces?

One complication for me is health, I cannot weld a chain saw anymore so I need it done so I can get it through my MM16 MiniMax bandsaw. No one seems interested. I could understand if I said here is what I want but it's got to be $20 or less per piece.

The wood I'm referring too is domestic stuff, not exotic.

Don

Re: If you had a big burly maple tree to sell. *LINK*

#5

So how would you saw that one?

Keith Newton----Little Rock, Arkansas

I know where there is one about like that on a vacant lot, that I'm hoping for.

Wish it didn't have a high voltage line so close to it, or I would have already tried to get it.

What kind of mill do you have?

Re: If you had a big burly maple tree to sell. *LINK*

#6

Re: If you had a big burly maple tree to sell.

Barbara Gill

Don, I am the exception but of course I am turner also. You bring up a good point. I will make a post to that.

Re: If you had a big burly maple tree to sell. *LINK*

#7

Re: So how would you saw that one?

Barbara Gill

Keith, I have a WoodMizer. I have sawn Cherry burls so large that I had to whack off a piece to pass. That was before I became a turner. I would have to actually see the log to be sure how I would saw it. If the burls did not go around the trunk, I would probably saw them off with a chainsaw. If they went around the trunk, factors like diameter would come into play.

I do know I would not saw thin pieces off unless I had a press. DAMHIKT

Re: If you had a big burly maple tree to sell. *LINK*

#8

Steven Antonucci

A press?

steven antonucci

I have some wood from a tree that was like the one in the picture, so I know what you mean about sawing it without having some way to control warping stresses.

When you say press, do you mean a way to weight the sawn boards flat above and beyond the stack and stickers? How mush "pressing" would you want? How thin would you cut it before you worried about warping?

Finally, would the press stop the faces of the boards from cracking?

Just wondering

Thanks

Steve

Re: If you had a big burly maple tree to sell. *LINK*

#9

Re: A press?

Keith Newton----Little Rock, Arkansas

Steve, I don't think there would be any way to keep that stuff flat, or from checking. Even if you could, any change in MC would cause some unfavorable warping.

If I want to use a burl for anything other than turning, I would rather just buy it as veneer.

Re: If you had a big burly maple tree to sell. *LINK*

#10

Re: A press?

Barbara Gill

Steve, if I were to cut veneer, I would build a veneer press. If I were to cut 4/4 I would build a press that used 4x4's on the top and bottom. I would space them no further than 18" apart. For each layer of boards, I would separate them with 3/4' stickers. I would drill holes in each 4x4 so that I could run all thread, depending upon the width of the stack 2-3 places per 4x4. The all thread would be the method to place equal pressure on the stack. You would need to check the tightness every once in awhile to keep the tightness. If the stack is small it is possible to use clamps instead of the all thread.

I doubt that I would ever again cut burl into 4/4 stock. I have had good luck cutting Cherry burl into 6/4 and thicker. It has remained stable with no cupping. In fact I think I still have a piece that is 5/4 that is stable.

Re: If you had a big burly maple tree to sell. *LINK*

#11

Re: A press?

Barbara Gill

I have not had a problem with Cherry Burl developing checks on the flat surfaces. You of course have to use good drying practices.

Re: If you had a big burly maple tree to sell. *LINK*

#12

Steven Antonucci

Thanks

steven antonucci

I think it would be very labor intensive to slab that tree and dry it without significant loss due to movement. Unless you were marketing to box makers, the odds of getting long, usuable lumber are pretty low.

That said, if you do get it right, it would probably be so cost prohibitive that most of us wouldn't be able to afford it.

S

Re: If you had a big burly maple tree to sell. *LINK*

#13

Re: Thanks

Barbara Gill

Not really Steve. As I said the thicker pieces at least of Cherry are nice and stable. I doubt that I would slab that tree except in short sections. I know of one turner here that used some of that Burl. As far as I know, it remained stable.

For me the pricing of the wood is related to the wood itself, not the sawing.

I would not be inclined to saw thin ( 1/2") pieces though.