Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

curved tool rest

Posts

curved tool rest

#1

curved tool rest

Skip Beardsley

I have a curved tool rest which I love using and went with my old Delta lathe. Since I got the new 3520b I find the shaft is not long enough to use in all applications on the new lathe.

Does anyone have any ideas where I can buy one with a shaft long enough to use on the new lathe?

Thanks

Skip

Re: curved tool rest

#2

Re: curved tool rest

Ralph Lindberg

Skip

Is it a single curve or an S curve

Single curve would be the Oneway or Robust

I don't know of an S curve that has a taller stem then the ol Delta I own...

Of course there is always welding another two inches of shaft on the Delta :D

Re: curved tool rest

#3

Re: curved tool rest

Doug Turner

Craft Supplies usa has an s curved tool rest with a threaded tool post. I don't know if they have the longer tool post for powermatic but you could send them an email inquiry. I have the same s curved threaded tool rest and don't use it. If you want to get a piece of 1" mild steel round stock and thread the end I would be happy to part with the tool rest for $10 plus shipping at cost.

Doug Turner

Re: curved tool rest

#5

Re: curved tool rest

Ralph Lindberg

Ya know, I didn't know Dave was making tool-rests, and I was just over to his place earlier this month!

Re: curved tool rest

#6

Re: curved tool rest

Bruce Smith

Skip, General Tool not General International manufacture a tool post extension that will extend the height of your tool rest post. If I understand your problem correctly I think this is what you are looking for. It is a 4 inch extension that is 1 inch male on one end and 1 inch female on the other with a locking key. this extension should allow you to use your old extension on your 3520B. I just checked my General catalogue and the part number for the extension is 2611. Google, General in Quebec Canada or get a hold of a dealer. Click on Lathe Accessories, there is a picture of it 3/4 of a way down the page. general@general.ca hope this helps out, good luck.

Re: curved tool rest

#7

Make your Own!

Jorge Casta�eda

Early in the game, I joined the Maine Woodturners and one of the very first activities was a hands on tool rest making session. I came with two curved ones, a long and a short I designed and made on the fly.

So I did luck out and learned it is quite simple if you can have access to the right equipment; since I've built two more and had a welder make me another two to my specs.

Six tool rest that cost me less than if I did buy a single one. And it was fun making them.

Re: curved tool rest

#8

Keith Tompkins

Re: curved tool rest

keith tompkins

Hi Bruce, I just picked up a buffing arbor from General 1 1/8LH threads for outboard use. Man, have prices gone up...my General cost $2300.00 new, now lists for 5K!

Re: curved tool rest

#9

Re: Make your Own! How?

Henry (Raleigh, NC)

So don't leave us all hanging. What are the right tools? A basic process description?

Henry

Re: curved tool rest

#11

Re: curved tool rest

Skip Beardsley

Ralph,

It is an S curve tool rest and I am told it may be made of cast iron and therefore not able to have an extension welded onto it.

Thanks to all for the links and suggestions. It gives me a direction to go to get this solved. I make lots of bowls and find the straight tool rest on the new lathe to be somewhat problematical.

Re: curved tool rest

#12

Re: curved tool rest

robo hippy

I have the S curved tool rest from Craft Supplies with the screw in post. I have used it a lot, mostly on smaller bowls. It is okay, but if you drop your gouge handle to shear cut, it is too broad, and gets in the way. I have the Oneway bowl rests also. I do like them, especially the outside one. The inside one will bounce a bit if you are roughing out on the very end of it. I now have the Robust Comfort bowl rests, and love them. The drill rod is far superior to the cast iron rests with almost no friction. The radius is about 12 inches, which is a bit tight for most of my larger bowls, but not for the medium sized ones. I do wish the inside rest was more of a J shape than a section of a circle. The support bar on it runs off at an angle rather than straight up and down, so you can get it really close to the wood, which you can't do with a straight up and down one. There is no bounce when working on the end of it. I guess if I had one of everything I wanted for tool rests, they would all have drill rod on them, and be in 1 inch increment radii (radiusses???) from about 6 to 16 inches.

robo hippy

Re: curved tool rest

#13

Re: Make your Own! How?

Jorge Casta�eda

Henry,

The main gear is a torch and and arc welder, plus a bench vise, hack saw or mechanical equivalent, wire brushes, files or hand held grinders,

For the original tool rests, we had a set of rollers, put a length of 1/2" x 1 1/2" flat bar crank the rollers and out of the other side a curved piece comes, shape as desired and weld to a round bar the proper size for your banjo, 1" for the Powermatic or Nova.

Without the rollers, we must heat up the bar to a dull red and forge it to shape, or use a thick metal plate with holes on it and insert pins on the holes and bend the heated piece around the pins, like my friend the welder did.

the metal I got from the scrap pile in the shipyard near by.

Pictures in a couple hours...

Re: curved tool rest

#14

Re: Make your Own! How?

Jorge Casta�eda

Here is a picture, top left, the original 2 made with the Maine Woodturners a curved interior at the top and right below it a curved exterior. Top right made by the welder, a whooper interior, all made of 1" round bar and a small curved interior.


Bottom left, one I made myself, bottom right is the rest from the Nova, I made one similar, with a longer post and 16" bar, could not find it, must be under a bunch of blanks.

As you see, nothing fancy, but functional.

Hope it help to motivate somebody...

Re: curved tool rest

#15

Re: Make your Own - sown the seed

Henry (Raleigh, NC)

Jorge:

Perfect - yes I'm inspired. My only tool rest is the one Nova supplied and that poses some challenges at times. Of course I have lots of other deficiencies (skills and tools) that also need improvement, but you've sown the seed here.

Thanks

Henry

Re: curved tool rest

#16

Re: Make your Own - sown the seed

Carole Valentine

If you chuck that tool rest supplied by Teknatool, I bet you find that your tuning improves dramatically! LOL Mine is in a drawer...didn't have to try it but once, and never used it again.

Re: curved tool rest

#17

Re: Make your Own - chuck it?

Henry (Raleigh, NC)

Carole; You have to be careful in choosing your terms here.

You want me to "chuck" that tool rest?

Facetiously - I guess the tool rest post will fit in my scroll chuck but I'm not sure I can squeeze it down to that diameter. :D :D

And once the 'piece' is chucked, then what? I'm an eager learner, but this has me confused!

Henry

Re: curved tool rest

#18

Steven Antonucci

Why don't you like the Teknatool rest?

steven antonucci

It's the one that I use almost all of the time?

Just wondering what your reasoning is.

Steve

Re: curved tool rest

#19

Keith Tompkins

Re: curved tool rest

keith tompkins

Hey Robo, I have that one as well. Once, it came loose when finishing a winged hollow form...it was just about finished when I saw the rest begin to swing outward...seemed like slow motion, then it hit the wings. BANG and it was gone, and my gouge was stuck in my palm. It won't happen again...it's welded tight.

Re: curved tool rest

#20

Re: curved tool rest

robo hippy

The idea of a screw in post makes as much sense to me as electric ceiling heat. I think mine is rusted in place. Can't understand why one would want to move the post.

robo hippy

Re: curved tool rest

#21

Re: Make your Own - sown the seed

Steve Harder

I JBWelded some drill rod to the top of my Nova toolrest - really improved tool handling across it.