Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Now for the hard question! What is ...

Posts

Now for the hard question! What is ...

#1

Now for the hard question! What is ...

Ed Moore in SW VA

it that makes a demo BAD? What are the things that a demonstrator should never do?

No names, please.

The phrase that I always hate to hear is "I've never turned one of these before, but I ..." And chances are it will be made obvious that they have not turned one before.

Ed

Re: Now for the hard question! What is ...

#2

Re: Now for the hard question! What is ...

john lucas

Don't just stand there and turn. That's boring. Tell me what you are doing and why at each step. If your just cutting from the rim to the bottom of the bowl, are you doing anything with the gouge. Maybe rotating the flute open or closed. If so why. Why did you pick that tool. Heck even just tell a story while your doing it. Unless your doing something that is so spectacular it doesn't need words you should be speaking.

Sanding. Everyone hates watching sanding. If people need to learn sanding then you could explain why and how and make a few passes to demonstrate. Don't stand there sanding from 120 to 1200 grit. That's just plain dull. Personally I don't sand at all during a demo unless it's some technique that needs to be show. I either toss that project when I get home or sand it later. The only time I will sand at all is when the piece will be donated to the club. Then I'll take my time to get the cuts cleaner, shear scrape and then hit is with 220 or higher to clean it up. If there's time after the demo I may finish sand and apply finish.

Re: Now for the hard question! What is ...

#3

Re: Now for the hard question! What is ...

Don Wilcut

Don't make excuses!!!!

Re: Now for the hard question! What is ...

#4

Steven Antonucci

Bad Demos have bad things happen

steven antonucci

Odd that this got posted below, but I'll repost here:

While we all know that stuff happens, bad stuff usually happens because of bad prep. If you can't finish something to completion, so be it. I've seen (and done) demos where the topic took longer than allotted and the demonstrator rushes the topic to finish.

In most of my demos these days, there is very little focus on the object being made and much more focus on the techniques used. I've seen demonstrators that are still thinking that they are producing a finished piece and those demos are usually pretty boring.

Steve

P.S. In one demo, a large chunk of wood flew into the audience. At least there was room in the front after that...

Re: Now for the hard question! What is ...

#5

Re: Now for the hard question! What is ...

Barbara Gill

No matter how good the demonstration is, if the audio and visual is poor then the demo is wasted. Camera placement is so important.

Re: Now for the hard question! What is ...

#6

Jim in Burlington Ont.

Re: Now for the hard question! What is ...

Jim in River Oaks, Ont.

Self promotion,

Some people have a desire to be Famous and use these types of demos to do that, being Famous is so important to some, Yuck!

Take care,

Jim

Re: Now for the hard question! What is ...

#7

Re: Now for the hard question! What is ...

Don at Central Illinois

While I have been to very few demos the CD's that I have I assume are similar to a live demo. Some of the demos, the sound is horrible. I know I'm getting older and didnt' take care of my ears while younger, but if I can't hear what the instructor is saying, or see what they are doing, I'm lost.

Re: Now for the hard question! What is ...

#8

Lack of organization and preparation!

JamieDonaldson

When a demonstrator has to turn his back to the audience and rummage about for the right tool, the flow of the demo is broken. :b

Re: Now for the hard question! What is ...

#9

Re: Now for the hard question! What is ...

robo hippy

There was a guy here in town that had a woodworking school, and he tried to do a class on the McNaughton coring system without ever using it before. I didn't even have to think about going to that one. He is no longer around.

You can talk too much, but if you are demoing turning technique, you have to keep the shavings going.

robo hippy

Re: Now for the hard question! What is ...

#10

Re: Now for the hard question! What is ...

Lan Brady

A couple of demo's stand out in my mind as being bad.

1. too many tool changes. He used 23 seperate tools to make a salad bowl. No explaination as to why.

2. Too many jokes, too little turning- It is a turning demo with some humor added. You are not a Comedian with a turning habit!

Lan

Re: Now for the hard question! What is ...

#11

Michael

Re: Now for the hard question! What is ...

Michael

If you make and or sell tools, please don't spend so much time and energy explaining why those in the audience should buy your tool. For instance you market a hollowing system and also do demos and it becomes painfully obvious to all in attendance that your primary aim is selling your tools.......at least make an effort to appear to be more interested in imparting your wisdom and knowledge rather than selling your equipment. Also, don't talk down to those in attendance, it's a turn-off. Don't pick out someone in the audience to screw with repeatedly, confirms you're a bore and bully. Finally, realize that there are more ways than your way to accomplish a task, it's not just your way or no way.

Re: Now for the hard question! What is ...

#12

Re: Now for the hard question! What is ...

Matt Birchfield

I've learned something from every demo I've been privileged to watch, but PLEASE, PLEASE don't talk down to the membership of a club, and/or ridicule your host.

Re: Now for the hard question! What is ...

#13

Re: Now for the hard question! What is ...

Nelson

I was at that same demo!!!!

Re: Now for the hard question! What is ...

#14

Michael

Re: Now for the hard question! What is ...

Michael

Yes lots have attended

Re: Now for the hard question! What is ...

#15

Re: Now for the hard question! What is ...

Clifton C

Ed, I like your questions but am not sure which one this reply would fall under. These are just some observations I�ve written to help me be a better demonstrator.

There are three questions that usually come up at a turning demo. In no particular order,

what wood are you using, at what speed are you turning and what angle are you using.

When you have a limited amount of time for a demo, I find it helps to anticipate, and answer these questions early on.

The wood used may or may not matter, however people do want to know. Even if its just FOG wood. (Found On Ground) Hey, it still gets a few laughs. And having fun is contagious.

As for speed, I�ve heard demonstrators state, �I�ve been turning so long, I don�t even pay attention to the speed.� While that may be true, it does not help the new wood turner. And a flippant reply is a turnoff for others.

For the tool angle, I�ve heard �I don�t know what I use, but it works for me� to �everyone uses a different angle, you have to find what works for you.� Again, this maybe true, but is of no help. A number is required, something that note takers can write down. (I�m a note taker.)

Thank you for your questions, I have new things to add to my �DDD� list.

Dos and Don�ts for Demos, a list I read, revise and reread on a regular basis�

c