Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Audiophile Help Requested

Posts

Audiophile Help Requested

#1

Audiophile Help Requested

charlie belden

This is a piece I'm working on and need some feedback / suggestions from anyone

who knows about speakers. I think it'll work but it no doubt can be improved.


Sugestions?

ps posted this to Messages as well. don't know how to post one message that can go to both forums.

Re: Audiophile Help Requested

#2

Steven Antonucci

If you goal is to reproduce ripples, yes

steven antonucci

Way back in the day, I designed audio equipment as an electrical engineering student. The one issue you will have is that you need to allow air to pass from front to back of your cabinet, which is why guitars and speaker have holes in them. If you don't, conceptually, you'llbe pulling against a vacuum.

By using styrofoam, you may get air to pass through the membrane and solve this, but I see it as more like a shaker table. I think the micro beads may work themselves into the foam, and plug up the air passages. All of this is guessing, of course...

I would probably make a thin membrane out of spruce if I wanted clear sound, or maple will do if you just want the waves. You can do it by turning a disc first, and then a backer plate with a very shallow recess in it. Simply insert your disc into the backer plate and turn it down to the recess flush. I made a disc for someone to pierce that was only .020 thick and 14" wide like this (you can almost read through it).

Perhaps a small, decorative sound hole at the bottom (more like a djembe?) than a bowl?

I watched your video, so I think I know what you are after...

Good luck.

Steve

Re: Audiophile Help Requested

#3

As an old "stereo speaker" builder, the

JamieDonaldson

. styrofoam will work against your purpose. It is more of a sound absorber than amplifier, and a thin membrane or soundboard (like wood) applied as a resonator would transfer the movement/sound far better. With a sealed enclosure, some of the power to flex the diaphragm is muted, but adding a back port to the enclosure will virtually eliminate the back pressure required to move the diaphragm. This is similar to designing a port reflex speaker enclosure, and air movement must be aimed toward the front, so to achieve max vibration of your surface for movement, the sealed enclosure will better.

Re: Audiophile Help Requested

#4

Re: If you goal is to reproduce ripples, yes

charlie belden

Thanks for providing things to think about.

The styrofoam I had in mind is a styrofoam "paper" plate. It's a closed cell styrofoam so the micro balloons and air can't get through it.

Hadn't thought of the need for free air on either side of the "membrane". There is a hole in the bttom "plug" for screwing in a sheet rock screw - so I can remove the plug for battery changes. Since this thing shouldn't be moving a lot of air that small hole may do the job. If not I can always enlarge it.

Because the bowl has an overhanging rim, whatever I use as a membrane has to be easy to cut and flexible enough to be bent to get it in the bowl and then spread back out to seal against the inside of the bowl.

I've got a Wok stand that's basically two metal rings with three legs connecting them - and leaving plenty of access room between them. It'll support membranes for prototyping. And this is going to take some trial and error so being able to change things will be important.

Whether this idea pans out and works as I hope it will or not, it's an interesting experience experimenting - both with the programming of the micro controller as well as playing with different ways of getting to where I want to go.

Re: Audiophile Help Requested

#5

Suggestion

Mark Mandell - Gone Round In Jersey

Charlie,

You might be helped in your quest by looking up "cymatics" which is the science/art of doing exactly what you're talking about. There's a Wiki article (of course) on it and a number of good links plus videos on You Tube as I posted a link on the Message board.

Let us know when you post your video! :D

Re: Audiophile Help Requested

#6

Chladni Plate  *LINK*

Doc Green

Charlie, I believe you're trying to reproduce a classic physics demonstration that traditionally used a metal plate, violin bow, etc., but which now can be done with electronic signal generators. For it to work, the vibrating membrane, plate, or whatever, has to be capable of resonance. I'm not sure an untensioned styrafoam plate will work.


Chladni Demo