Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Turning acrylic

Posts

Turning acrylic

#1

Turning acrylic

Mike Foster

I posted a pic of a new piece on WOW last night and got a lot of feedback regarding my first choice of base. It really attracted the eye more than I would like. I got a few suggestions of using clear acrylic for the base. I've never tried turning acrylic and wondered how it behaves. Is it spendy? How do you finish it to get it looking clear? Anyone have any sources? So many questions. I usually just leap into something like this, but if anyone has experience with it I'm sure it can only help.

Mike

Re: Turning acrylic

#2

Re: Turning acrylic *LINK*

Ed Davidson

Mike,

When people use the word �acrylic� they often mean plastic, which could be any number of materials. If you�re wanting a clear glass-like turned finish, there are several options to choose from. You could cast your own blank from a material like Polyester Resin, sold by Michael�s and Hobby Lobby in small size (1 quart or less) containers. Or you could turn some pre-cast acrylic rod. If you go this route, be sure to buy cast, and not extruded acrylic rod, turn it with skews and scrapers (negative rake or remove the burr), wet sand up to 1,000 grit or so and buff using a system like Beall. Here's a finished example of clear cast acrylic from a 2" diameter rod. I get cast acrylic rod from the link below.


img

Delvie's Plastics

Re: Turning acrylic

#3

Re: Turning acrylic

Jeff Willaford

I use a skew or a drop-nose scraper for acrylics. It can be chippy if I get too agressive but once rounded I get nice long strings off it. Have to stop from time to time and clear them. Wet sanding with 3M wet or dry polishing sheets brings it up to a nice clear finish. Try an acrylic pen blank or just turn a piece of PVC and you'll see how it cuts.

Re: Turning acrylic

#4

Re: Turning acrylic

Coyne

I haven't had a lot of experience with it, but found that warming PVC to slightly warm to the touch greatly decreased the 'chipiness'. Coyne

Re: Turning acrylic

#5

Re: Turning acrylic

Ron McKinley

Jeff: Is a drop-nose scraper the same as a negative rake scraper? ....Ron

Re: Turning acrylic

#6

Thanks

Mike Foster

Thanks for the tips. I am going to give it a go. Something new and different, oh boy.

Re: Turning acrylic

#7

Re: Thanks

John Lucas

Mike I've found that you have to "feel" the cut. If you push too hard it chips. Use sharp tools and let the tool do the cutting. When you get the shavings that stick to your arm and everything else in the shop then your doing it right.

Re: Turning acrylic

#8

Re: Turning acrylic

Dave Long

Mike, you might get in touch with Harvey Fein. He does a lot of acrylic bases for his work.

Re: Turning acrylic

#9

Re: re. ornaments

Fred Holder

My only experience turning Acrilic was these two balls. One Pink cast acriic and the other is Black PVC. As others have said, use negative rake scrapers. You can get shavings that are 20 to 30 feet long and that like to wind around everything. Good luck.


Re: Turning acrylic

#10

Re: Turning acrylic

Ace Foster

What's the difference in turning properties between cast and extruded? I have a little trouble seeing why it would matter.

Re: Turning acrylic

#11

Re: Turning acrylic

Jeff Willaford

Ron, I''m not smart enough to know but ... Myron Curtis gets credit for the drop nose scraper style I use made from 1/4" square hss. Attached is a picture pilfered from Matt Lewis' gallery on AAW. I hope Matt doesn't mind.


Re: Turning acrylic

#12

Re: Turning acrylic

Ed Davidson

Envision how the two types of acrylic are made � extruding the material tends to organize the molecules in one direction, causing brittleness. Cast material on the other hand, is randomly organized, stronger and less likely to explode if you get a catch.

BTW, there is a test you can run to see what type acrylic you have � cut a piece on the band saw. If it�s extruded, the material around the cut will melt. If it�s cast, you�ll get a clean cut with no sign of melting.