Simple enough question. Anyone got some shop time today? If so, what are you working on?
I just finished a major shop overhaul so I am finally getting some turning done in 2011. I've got a couple of ash bowls under my belt and a pair of plate/platter thingies. Took me a while to remember which end of the gouge to hold!
Be well everybody!
P.S. The link is to my blog which gives the gory details of the clean-up. If the moderators feel it is inappropriate for me to link to my blog, feel free to delete.
Shop time today, yep, I'm going to finish up some production work (crochet hooks), and then get to roughing out some bowls. (A dear friend gave me LOTS of half-logs of Russian Olive). It smells quite lovely when cut, and makes a beautiful natural edge because of the sharp contrast in color between the heart- and sap-wood.
If I have time, I might even treat myself to a burl bowl... some yummy thuya and maple burl arrived just yesterday and is calling to me...
Katherine - just a heads-up - Russian Olive (Eleagnus angustifolia) is quite prone to ring shake, so keep an eye on your bowls as you rough them out. I've had more than one come apart on the lathe for me, so just sending-along that bit of advice.
Very nice article in AW (!) and thanks for the feedback on Special Interest Night - I will put out a formal call for participants shortly, but it seems there is enough interest in trying a "Gizmos and Gadgets" discussion and allowing the experiment to run - (people will vote with their feet!). (BTW - I have you down as possibly bringing something to show.....!! Thanks!)
This morning I finished teaching a Biology laboratory on liverworts and hornworts (small, non-vascular land plants) to my class in Plant Evolution.....therefore, "day-job" is mostly done already for today.
This afternoon I will be teaching the second of four "Lifelong Learning" (="College for Seniors") classes in woodturning to about 13 interested senior citizens. I'll continue-on from last week's introduction with basics of turning spindles; I'll turn a finger top, a bottle stopper, and then will wrap-up today with turning a pen. (.....next week, we're on to turning bowls, and the following week, hollow forms).
I suppose I'm bringing the shop to the classroom (Jet Mini-lathe, etc.), so I guess I have SOME shop time today!! Not sure if I'll have any shop time in MY shop though!
Rob, Thanks for the info! I've already run into a couple of pieces where the rings have separated from one another... luckily, I observed the peculiarity in sound and was able to turn the lathe off in time. (It sounds like the wall is getting quite thin... which of course shouldn't be, since it was more than an inch thick at the time!)
What causes ring shake? (Anything I can do to prevent it?)
Thanks for the compliment on my article! I'm really excited about your "Gizmos and Gadgets" topic -- looking forward to it!
Sitting at my desk at home working through 300+ emails in my inbox while fighting off the flu; I should be down at the lathe finishing the cherry bowl I started. Plus I have a half dozen blanks from Dan Bailey begging to be turned.
I'm not sure, but I think ring shake is a defect in the tree not caused by cutting or processing the wood. Like "character" you don't create it, your work just reveals it.
Ok, being sick is definately not awesome. Feel better. As for me, I ran errands, appointments and soon, soccer practice for a short person. Later tonight, Manitoba Maple which is flaming red. I hope it has some figure in it.
Barry is correct, you don't induce ring shake by turning methods, it's just a defect in the wood. Ring shake is usually caused by some physical environmental stress on the tree (can be due to excessive wind, or more commonly, snow or ice loading) which causes adjacent annual growth rings to break apart and create (usually hidden) cracks that follow the growth ring (circumferential cracks), and when the stress(es) is/are relieved the tree reverts to its unstressed position, and the cracks appear to close. The tree can go on growing without much problem with these cracks, however when the wood is cut and turned, such cracks can create a nasty surprise, particularly if the piece decides not to stay together any more while spinning on the lathe!
I have read also that some tree felling practices may also contribute to ring shake (such as felling large trees improperly e.g. on top of other logs) which can cause excessive flex in the timber as it hits the ground.
I have had some limited success in repairing bowls and vessels with ring shake defects by using CA glue before the piece dries fully,a nd filling some cracks with sawdust and CA. I prefer not o have to do this, and if teh hake is really bad while turning, I'll not waste any more time and discard the blank and start over on a fresh one.
Like John Jordan says, "Life's too short to turn crappy wood".