Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Coloring Epoxy

Posts

Coloring Epoxy

#1

Coloring Epoxy

Tony - Memphis

I did a search here the other day looking for some ideas on how to tint epoxy. Got some good ideas - thanks all. I am turning some of those laser cut pens and needed some black filler for the seams. I tried ground up pastel chalk and it worked very well. Didn't take much either. I just used sandpaper to "grind" the pastel and collected it in a cup. Then mixed it in with 5 min epoxy and it worked great.

Tony

Re: Coloring Epoxy

#2

Re: Coloring Epoxy

John Lucas

Tony It does work well and so does copier toner. They both thicken it slightly. If you still need thin epoxy try using Feibings black shoe dye.

Re: Coloring Epoxy

#4

Re: Coloring Epoxy

john lucas

You may have used too much or it could be the brand of epoxy. I use West system and have used System 3 and both worked fine. I have also tinted a lot of the cheap syringe types with shoe dye. It doesn't take much.

Re: Coloring Epoxy

#5

George Taylor

Black CA glue

George Taylor

There is also black CA glue on the market (Starbond?); our club got some samples ... have not tried it yet.

George

Re: Coloring Epoxy

#6

Richard Allen

Re: Coloring Epoxy

Richard Allen

I "wet" the surface with epoxy. Then add a little filler to the epoxy and add a little dye to the epoxy and apply that.

The wetting forms a barrier to the colored epoxy so the color doesn't bleed into the wood.

The filler makes the epoxy opaque.

The dye, I use powder reactive dye in very small amounts, to add the desired color to the epoxy.

I use west system epoxy with the slow hardener. I have found that the 5 minute epoxy never gets hard.

Re: Coloring Epoxy

#7

Re: Coloring Epoxy

john lucas

Richard Which 5 minute epoxy are you using? I have used various brands of 5 minute epoxy and also West System rapid hardener. The only time I've had trouble with them not getting hard is when I used the wrong mixture.

I have had problems when I mix too much colorant or particular types of colorant.

Re: Coloring Epoxy

#8

Richard Allen

Re: Coloring Epoxy

Richard Allen

The non-hardening of 5 minute epoxy I used was system 3 "Quick Cure".

I went through most the the epoxy over a year and I never tried it again.

Perhaps my observations are the result of old glue.

Re: Coloring Epoxy

#9

Re: Black CA glue

Emmett Manley, Lakeland, TN

I received some black CA glue as a Christmas present. Without the accelerator, this CA glue did not cure overnight; whereas, the usual CA glue sets up in a matter of minutes, if not seconds. My black CA glue also shrunk a lot. Bottom line -- I am very unhappy with the black CA glue I have. Mine came from Craft.

Re: Coloring Epoxy

#10

Re: Coloring Epoxy

John Lucas

Richard I go through glue so fast it never gets old. When I have a problem with non hardening glue it's usually been that I mixed too much of something else into it or I possibly mixed uneven quantites of A and B. I suppose old glue could be a problem. Maybe I need to buy larger quantities. :)

Re: Coloring Epoxy

#11

Ric Taylor

Re: Black CA glue

Ric Taylor

My experience with the black CA glue from Starbond is that it shrinks over time, long after the piece is finished. I won't be using it again.

Ric

Re: Coloring Epoxy

#12

Jim Evans

Re: Coloring Epoxy

Jim Evans

I have had good luck using Jaquards Pearlescent powders. For most of my coloring I use the end of a Popsicle stick which is about 1/4 teaspoon full.

Re: Coloring Epoxy

#13

Jim Evans

Re: Coloring Epoxy

Jim Evans

Dang I forgot the link.

http://www.jacquardproducts.com/products/pearlex/powders/