Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

New Shop Design & Layout Help ?

Posts

New Shop Design & Layout Help ?

#1

Brad Vietje

New Shop Design & Layout Help ?

Brad Vietje

Hi Folks,

I've been away from active turning for well over a year now, as our new home has been under construction; the building we are living in will become my new shop space -- aaah -- a heated space, at last!!!

I will be setting up a turning shop, not a furniture-making shop. I will have 3 -4 lathes, (eventually it will be a teaching space), a bandsaw, a ceiling crane for heavy green logs above the big lathe, a sharpening station (probably on wheels), a dust extractor, a finishing room, a drying area or room, wood storage, and a shed area for rough cutting and chain saw work. I will also bring in some "flat work" tools to assist with wood trim and such in the new house (radial arm saw, router table, and such), but these will have to roll away for storage, as I'm not planning on doing much flat work.

I have two questions:

1. Are there good resources on shop layout that are specific to turning? I'm particularly interested in the movement of wood through the turning process from green to rough to drying to finish turning and finishing, as well as using sources of daylight, and other such factors.

2. Has anyone worked on shop design as a club activity? Results? I may try to get the club think tank fired up and approach this as a group activity...

Thanks in advance for your ideas,

Brad Vietje

Newbury, VT

Re: New Shop Design & Layout Help ?

#2

Re: New Shop Design & Layout Help ?

Mark Wollschlager

The article below lists a couple of workshop design and setup books:

http://www.woodworking.org/WC/GArchive00/5_26mattsonshoprev.html

The Grizzly workshop planner is a free interactive shop designer

http://grizzly.com/workshopplanner.aspx

Some more tips for workshop setup:

http://woodworking.about.com/od/shopdesignlayout/Wood_Shop_Design_And_Layout.htm

And of course Shop Shots here on WoodCentral

color me envious, by the way.

I have been given permission to dream of a new shop.

A new kitchen and a short laundry list of other home improvements stand in its way.

We can enjoy a new shop vicariously through you.

Post lots of pics.

Mark.

Re: New Shop Design & Layout Help ?

#3

JL

Re: New Shop Design & Layout Help ?

JL

I like the Grizzly "Dream Shop Workshop Planner" on the Grizzly.com site. I think it is one of the better "layout" tools.

It has a variety of tools (Grizzly, of course) that you can place in locations and move around. You can save your plans and layout.

Re: New Shop Design & Layout Help ?

#4

Steven Antonucci

Things that I would work into a design:

steven antonucci

I would have a storage area for anchorseal and chainsaw gas right by an outside door. I have run the saw inside of the garage, once, and it took three days for the smell to leave. I'd own an electric chainsaw for inside.

I've also anchorsealed on the shop floor, and newspapers aren't always the best answer. I'd probably want a "potting bench" for slopping it on without worrying, and I guess it would be nice to be able to do it indoors some days.

Ellsworth's shop is laid out so that no other turner is in another turner's line of fire incase someone has defective walnut (joking, Lance ;) . This takes a lot of thought when you also are trying to avoid putting a window for natural light in the line of fire too.

It also makes a lot of sense to centralize grinding/sharpening, even if you have multiple lathes. if there is a way to arrange a door to the outside, a leafblower will help you clean house when you really need to get er done. Can't have it blowing on the walkway though...

I recommend setting up the shop for the 80% and making 20% the exception. I just stored a bunch of things that are useful, but not used every day. 2/3 of my tools are now in a drawer, and I am much happier...

Steve

Re: New Shop Design & Layout Help ?

#5

Re: My dream turning shop would have...

Wayne Kuhn

a door I could back my truck into with an overhead hoist to lift the logs off the truck into a storage area with a chainsaw station and overhead exhaust similar to a indoor welding station.

From there it would go to the bandsaw, then to the roughing lathe. After the roughing lathe into the drying kiln that is temperature and humidity controlled.

Next station would be the finishing lathes-1 for bowls, 1 for hollow forms and one for pens and such, all electronic variable speed.

From there it would go to the Carving, burning ,texturing station again with overhead exhaust.

Into the finishing booth with exhaust and filters. Then to the curing room. Out of the curing room into my on-site gallery. A full bathroom, and office would also be incorporated. Dust collection at all stations with floor sweeps as well as hand-helds with the main unit outside. Pressurized Air would also be supplied at all stations with compressor out side as well. Music piped throughout. I would also have a mechanics station for the various maintenance duties required. Ahhh someday.......

Wayne Kuhn

Columbia, MD

Re: New Shop Design & Layout Help ?

#6

Bill Blasic

Re: My dream turning shop would have...

Bill Blasic

Brad,

Unless your extremely lucky you will find yourself rearranging your studio more than once. That is based on my own experience, hey enjoy the ride!

Bill

Re: New Shop Design & Layout Help ?

#7

Steven Antonucci

revisiting how my shop is laid out is my fav proj!

steven antonucci

I can't even remember all of the various layouts I've had over the years? The shop I am in today is a metamorphasis of how I work (today) from how I have worked over the years. I would have never built it this way from bare walls today, but 10 years from now, it won't look like it does today either!

S

Re: New Shop Design & Layout Help ?

#8

Re: New Shop Design & Layout Help ?

Mike Foster

Brad, good to hear your getting the lathe cranked up and out of the cold. A heated shop is really nice up here in VT. I can't help you with the design, as you know, my shop was really built as a multipurpose tool. I still use it to do flat work as well as turning. I got a new lathe at the last symposium (it's a real beauty), and decided that turning needed to take center stage. Found a way to reposition things so the lathe is out in the open and away from all walls, but I can still use the table saw and bandsaw with no interference. I would suggest talking to Hannes. He's done it for a long time and would be full of good ideas. I'm sure he'd be more than glad to help.

Mike

Re: New Shop Design & Layout Help ?

#9

Re: New Shop Design & Layout Help ?

John Stroud

Constructing a new shop (studio?) was my retirement present. 850 SF with 12' ceilings. I had planned to put all of my equipment except my lathe on island but that will be later. My lathe is in the corner with two windows that overlook a golf course. Perfect lighting and I feel like the space is much larger than it really is. My tools are behind me in a tool rack learned from a workshop at Craft Supply. The entrance is designed with shelves for displaying my turnings and I have a small area separated for finishing..Let the chips fly!