Backer plate
Don at Central Illinios
Does Richard Joyner have a web site where I can purchase the offset backer plate?
Knowledge You Can Build On — Est. 1998
Backer plate
Don at Central Illinios
Does Richard Joyner have a web site where I can purchase the offset backer plate?
Re: Backer plate
Alan Zenreich
I don't think he has a web site, but there are a few ways to get a backer plate
Here's some information from a workshop I taught in October.
I hope this helps.
Pendant backer plate
� Manufactured by Richard Joyner (�Sailing_away� member at http://www.penturners.org)
� Phone 727-254-9808
� The cost is $54.95 for the Deluxe which includes shipping anywhere in the U.S.
� He accepts PayPal, check or money order.
� His PayPal info is richardj1169@yahoo.com
There is a thread on Penturners.org that shows the item http://www.penturners.org/forum/showthread.php?t=48855
� His version comes with thumbscrews, not allen screws
� Note, though some versions come with hex screws (so they don�t interfere with any mandrel positions) Lauren and I prefer the thumb screw version because we often change the indexing of the top plate and want to do it tool free. If the mandrel position interferes with a thumbscrew, simply leave that screw out. Two or three screws is just fine, you don�t need all four.
� Most bottle stopper mandrels will fit. Mandrel needs a 3/8�x16tpi thread, you can make your own
Also available from Ruth Niles at www.Torne-Lignum.com $50 + shipping
The pendant plate package includes the faceplate, the eccentric plate, 4 screws with washers and the allen wrench.
Pendant Samples and step by step
� http://www.torne-lignum.com/Pendant-chucks.html
� Ruth�s MT2 mandrel for bottle stoppers works $25 (needs a washer or thread trim to seat properly on backer plate)
http://www.torne-lignum.com/stoppers.html
Also available from Steve Worcester�s web site
� http://www.turningwood.com/pendant_jig.htm $55 +$6 SH
� http://www.turningwood.com/mm5/merchant.mvc?Screen=PROD&Store_Code=T&Product_Code=RJPJ&Category_Code=JT
==========
Tutorials
The tool is fairly easy to useHere are some links with the tutorials.
� http://www.penturners.org/forum/showthread.php?t=49636&highlight=pendant
� http://www.penturners.org/forum/showthread.php?t=55731
� http://www.penturners.org/forum/showthread.php?t=316
YoYo Spin - Ed Davidson videos
� http://yoyospin.com/videos/pendant_1.wmv
� http://yoyospin.com/videos/pendant_2.wmv
Ruth Niles sells it
Re: Ruth Niles sells it
Don at Central Illinios
Thanks. Between you and the previous poster, I have plenty of options.
Re: Backer plate
Bill Turpin in WNC mountains
Make your starting blanks as close to round as possible before tapeing to the Joyner. Tape does not like sudden bumps.
Steve Worcester sells it too..... *LINK*
Rob Wallace
Also has a description page at the link below...
Rob Wallace
Steve Worcester's Pendant Page
Re: Steve Worcester sells it too.....
steve worcester
Since I know Richard and Ruth, buy from who you like. We are all good people (I know, kind of a humble opinion). But I would like to see more recipes for pendants. It is a fun device to explore with.
If you need sandpaper...........
Ruth Niles
If you need good sandpaper, buy it from Steve and get the pendant plate with the same order. Like Steve said, we're all good guys. : )
Re: If you need sandpaper...........
Alan Zenreich
Ruth,
You're definately not a guy!
Re: If you need sandpaper...........
steve worcester
True. it was used in a generic state.
But I do hold Ruth in high regard too