Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Pendant - redesign opportunity

Posts

Pendant - redesign opportunity

#1

Alan Zenreich

Pendant - redesign opportunity

Alan Zenreich

I've posted this today in a few other forums I frequent. However, I rarely post any projects here, and thought you might be entertained.

This stabilized buckeye burl pendant was intended to be round with an offset 5/8" hole.

However, things do not always go as planned.

When boring the center hole on the drill press, a small chunk came off of the blank. Some epoxy, dried coffee grinds, and voodoo let me put it back together again.

However with the blank mounted on the pendant backer plate, I was shaping the outer edge when a larger chunk went into orbit somewhere in the shop. This was not repairable.

Undetered, I took this as a 'redesign opportunity'.

Back to the drill press, with a larger forstner bit to rough out a moon profile.

Then back to the lathe, using the forstner bit in the tailstock to align the blank around the new eccentric center. A little shaping of the inner curve took a few minutes... keeping in mind that there's not much wood being held onto by the double sided tape.

Because of the shape, there's lots of air being turned... delicate stuff.

Next, recenter the blank and shape the outside edge. then remove from the backer plate, and follow up with some final shaping using sanding mops, then on to my first use of Deft water based lacquer. Lauren wanted this piece to be a little glossy.

Finally, I had to drill two tiny holes for the screw eye findings. Trick was deciding where they should be placed so the moon would be at a slight angle when the necklace and beading were attached. Lauren had already prepared the crystals and chainwork.

We got the pendant done just in time for a black tie wedding a few weeks back. I was in a tux, and Lauren wore the pendant on a black dress. It looked lovely on her.

So, this was not what we intended to make. But the forces in the universe kept saying "you don't want to make that... you want to make this..."

Sometimes it pays to just go with the flow and see what was hiding in the materials.


img

Re: Pendant - redesign opportunity

#2

Ellis Walentine

That's gorgeous, Alan

Ellis Walentine

Call it serendipity, if you will, but going with the flow is always easier than swimming upstream.

Thanks for posting.

Ellis

Re: Pendant - redesign opportunity

#3

Re: Pendant - redesign opportunity

charlie belden

Muses often whisper hints. This muse gave you fair warning that you were heading in the wrong direction - TWICE. And when you finally got the message, the muse helped make some tricky turning work out just to let you know you were back on track. The results show that the muse was right - and that you followed hints very nicely. You don't need diamonds to make a nice piece of jewelry - as you've clearly demonstrated.

(I've got this image of a naked guy, wearing a black tie, standing with a beautiful woman in a black dress, wearing a gorgeous necklace.)

Re: Pendant - redesign opportunity

#4

Alan Zenreich

Re: Pendant - redesign opportunity

Alan Zenreich

Charlie, when a wedding is held at a nudist camp, you can always tell who the "best" man is.

Re: Pendant - redesign opportunity

#5

GROAN

charlie belden

Re: Pendant - redesign opportunity

#6

Re: Pendant - redesign opportunity

Bruce

Charlie, that is not a pretty picture you paint. Now I gotta go gut a pig to lose that image.

Lovely pendant!

Re: Pendant - redesign opportunity

#7

Re: Pendant - redesign opportunity

bill Crommett

Charlie: Your fantasy about the naked man reminded me of the hours I spent at the airport mentally undressing the women that walked by. That was until I found it more amusing to mentally undress the men.

I didn't have to spend time in the State Hospital to get cured. Old age took care of that.

It must have been a good idea, because years later the TSA has gotten in the act.