Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

1.25" x 8 TPI nut

Posts

1.25" x 8 TPI nut

#1

1.25" x 8 TPI nut

Starry S Chan

Does anyone know where I can find 1.25" x 8 TPI nuts? Instead of using face plates, I would like to use these nuts to make a few vacuum chucks.

Starry

Re: 1.25" x 8 TPI nut

#2

Walt Bennett

Re: 1.25" x 8 TPI nut

Walt Bennett

Ask Bill Noble - william_b_noble@msn.com

Re: 1.25" x 8 TPI nut

#3

Rob Wallace

Re: 1.25" x 8 TPI nut *LINK*

Rob Wallace

I have purchased them before from MSC. Be sure to get the 1-1/4"x8 tpi and not the more common 7 tpi. Link below.

Rob Wallace


1-1/4" 8 tpi nuts from MSC

Re: 1.25" x 8 TPI nut

#4

Re: 1.25" x 8 TPI nut

Randy Johnson

Why not buy a Beal tap and just make the entire thing out of wood?

I haven�t gone the vacuum route yet but that is the way I make all my jam chucks.

Re: 1.25" x 8 TPI nut

#5

Tap  . . . What Randy said.

Doc Green

Starry, it's not a big deal to make a vacuum chuck out of MDF or plywood, or even solid wood, but you have to have a tap. You can get one from Packard Woodworks, Craft Supplies, or from the Beall Tool Company directly. ~Doc

Re: 1.25" x 8 TPI nut

#6

Re: 1.25" x 8 TPI nut

Bill Howatt

Most of my vacuum chucks are made of a piece of 3/4 MDF drilled and tapped 1.25"x8 with a groove cut into them with a parting tool. In the groove I expoxy a large ABS pipe joiner (bit bigger in dia than the pipe). I true the top edge then glue some closed-cell foam around the edge for a gasket.

When you are using a vacuum chuck you are typically dealing with a dry almost fully-turned, blanced, piece which is very light compared to a wet blank so the above method has more than enough strength.

Bill

Re: 1.25" x 8 TPI nut

#7

Re: 1.25" x 8 TPI nut

Bill McWhirter

My local Fastenal store has them in stock generally.

Re: 1.25" x 8 TPI nut

#8

Re: 1.25" x 8 TPI nut

john lucas

Well you've gotten all the good answers. I get mine from either MSC or Fastenal. I also have the Beal tap and highly recommend it. The nuts aren't cheap because they are a special type of material and that's whey they have that thread. I use plastic decking material to make my chucks and use the Beal tap to thread them.

Re: 1.25" x 8 TPI nut

#9

dito

JohnKyler

Re: 1.25" x 8 TPI nut

#10

Grainger has them

Gil Jones

Re: 1.25" x 8 TPI nut

#11

Re: 1.25" x 8 TPI nut

Nick Tuzzolino

John: What kind of glue to you use to attach wood to the plastic decking? Is there a name for this decking.? I've seen some around, but not sure they are all the same.

Re: 1.25" x 8 TPI nut

#12

Re: 1.25" x 8 TPI nut

Barry Irby

I buy mine at a local salvage/scrap yard. Have to VERY careful to get the 8 thread version rather than the the 7 thread and it is difficult to look at them and tell he difference. I know the people that run the yard and they let me buy a handful, take them home and try them and return and swap the ones that don't work. It would be too much trouble if they weren't local. I need one of those "combs" to measure the threads, but once I got about 20, it was a lifetime supply. I also bought "blind plates" (four inch round disks) and had a local machinist make me about six faceplates.

Re: 1.25" x 8 TPI nut

#13

McMaster Carr

Ron Bauman

Probably various ratings:http://www.mcmaster.com/#hex-nuts/=a8bhd1

Re: 1.25" x 8 TPI nut

#14

Re: 1.25" x 8 TPI nut

Steve Worcester

the machinist part is rather critical. If you weld a washer onto the nut, you you have to make sure it runs true in all directions.

Re: 1.25" x 8 TPI nut

#15

Re: 1.25" x 8 TPI nut

Barry Irby

You are correct. The machinist that did mine welded them and then mounted them on a metal lathe and "faced" them off and trued the rim. He did not charge me enough, but he is retired and pretends to make a little money in his shop the same way I do in mine.

Re: 1.25" x 8 TPI nut

#16

Thank you for your replies

Starry S Chan

Thank you for your replies, especially the one from John Lucas. I do not know John but I read a lot of his postings and I am always very impressed by his work. I appreciate that he took time to reply to my posting even in his grieving period.

In any case, I went ahead to order a Beall 1.25x8TPI spindle tap. This is the best solution as it allows me to make both jam chuck and vacuum chuck.

Starry Chan