Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Shop made lathe stand and storage

Posts

Shop made lathe stand and storage

#1

Shop made lathe stand and storage

Todd Nebel

I just completed finishing this lathe stand. This is my own design. I built it out of QSWO and poplar for the drawers. Through dovetails on the case and half-blind on the drawers. It's real heavy by itself and even better filled. My design allows maximum space under the lathe to prevent wood chips from building up under the motor and belt. It also allow easy belt changes with or without opening the access door. Can't wait to try it out this weekend. I'll post a couple other shots to follow.


img

Re: Shop made lathe stand and storage

#2

Pic 2

Todd Nebel

Close up.


img

Re: Shop made lathe stand and storage

#3

Pic 3

Todd Nebel

Storage


img

Re: Shop made lathe stand and storage

#4

Pic 4

Todd Nebel

What's nice is while working on a project, you can still see what chisel to grab by looking over and down.


img

Re: Shop made lathe stand and storage

#5

Dick Hines

Re: Pic 4

Dick Hines

Todd, once you get on a real turning spree you will only know that your tools have brown or clear handles.

Re: Shop made lathe stand and storage

#6

Re: Shop made lathe stand and storage

Don Orr

Mighty fine piece of work Todd. I hope it give you many years of turning pleasure.

Re: Shop made lathe stand and storage

#7

Bob Moffett

Re: Shop made lathe stand and storage

Bob Moffett

That's really nice but, it needs some shavings on it. Great work.

Re: Shop made lathe stand and storage

#8

Harry Robinette

Re: Pic 3

Harry Robinette

Very nice stand like the tool holder that the chips can fall through.

Re: Shop made lathe stand and storage

#9

Hey Bob

Todd Nebel

Here's some of those shavings...


img

Re: Shop made lathe stand and storage

#10

Bob Moffett

Re: Hey Bob

Bob Moffett

That's a very nice piece that you turned. The shavings look good also. lol

Re: Shop made lathe stand and storage

#11

Brad Vietje

Re: Hey Bob

Brad Vietje

Hey Todd,

Now that's better! That's a handsome lathe work station, and as Bob writes, a nice turning there, too.

I think my preference would be for the lathe to be mounted further forward -- that is, further from the wall, and more above the front edge of the drawers, as pictured. If the contents weigh enough for counter-balance, I would find it easier on my back to avoid leaning forward. As for tool recognition, I don't have tools that look so much alike from the handle ends, and have colored, woodburned, or in some way marked those that did look alike so they could be easily recognized.

I've seen a similar cabinet stand design with the lathe further forward, and the tool rack at a steep, nearly vertical angle behind it. The top of the cabinet was slanted to allow shavings to be collected by a box or bag behind the lathe stand.

I hope you get many years of turning joy with your new setup.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Shop made lathe stand and storage

#12

Re: Hey Bob

Todd Nebel

Now here's how it looks after 6 or so bowls...


img

Re: Shop made lathe stand and storage

#13

(Message Deleted by Poster)

Galen Vetterick

Re: Shop made lathe stand and storage

#14

Re: Hey Bob

bill Crommett

Tod: ignore Galen. You will never have enough room. Joe Murphy's third law says that any work space will quickly be filled to the extent that it will become inefficient . This is similar to the law that says that three moves is as good as a fire, but we would prefer not to mention any thing about a fire in the workshop.

Re: Shop made lathe stand and storage

#15

Re: Hey Bob

Frederick Nelson

Now, that looks more like it should.

Fred

Cold and bleak in Eastern Missouri