Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Looking for very small brass screw eyes

Posts

Looking for very small brass screw eyes

#1

Looking for very small brass screw eyes

Larry In Lima

Well, subject says it all I guess. I'm looking for some very very small brass screw eyes. I'd prefer solid brass, but any would be more than I"ve found so far. Many web sites don't even specify what size they are, but they want you to buy them??? Go figure...

I've made some very small ornaments, maybe 1" tall that I'd like to hang. Christmas trees, snowmen.... Granddaughter's idea so trying to make her happy. Larger would have been so much easier, in so many ways but it's done now!

Any help on brass screw eyes appreciated. I know I could improvise, but not ready to give up yet. Thanks, Larry

Re: Looking for very small brass screw eyes

#2

Re: Looking for very small brass screw eyes

Carole Valentine

If you can't find ones small enough to suit you, you can snip the eyes off of fish hooks and epoxy them in place.

Re: Looking for very small brass screw eyes

#3

Spence

Re: Looking for very small brass screw eyes

Spence

Make your own. This is what I do. Take some brass wire that would be about the size of the eye you want. Fold the wire over a nail and clamp the wire ends in a vise. I use a fly tier's vise. Then twist the wire. Presto! Drill the hole in the ornament and use a small drop of glue and sink your eye right up to the shoulders and your done. When I get going I can make 3 or 4 eyes a minute. Hope this helps!

Re: Looking for very small brass screw eyes

#4

Re: Looking for very small brass screw eyes

Larry In Lima

I like that idea Carole, if I can't find small brass eyes, I'l try it. Maybe someone will know of some, but I haven't had any luck. Larry

Re: Looking for very small brass screw eyes

#5

Re: Looking for very small brass screw eyes

J. Paul Fennell

Larry,

Look in McMaster Carr's catalog. The link is http://www.mcmaster.com/#screw-eyes/=9tdl6a.

Their smallest is 1/8" opening, in plated steel, stainless and brass.

Paul

Re: Looking for very small brass screw eyes

#6

Re: Looking for very small brass screw eyes

Bernie Weishapl

I make about 50 ornaments a year and like you had trouble finding small screw eyes. I started doing like Spence does. I sit down at night to watch TV and take about a 1" length 24 ga wire fold it in half around a small piece of round steel holding the ends with a pliers and twist. I can do 70 or 80 in a sitting watching TV at night and have a supply that will last for ages.

Re: Looking for very small brass screw eyes

#7

Dick Hines

Re: Looking for very small brass screw eyes

Dick Hines

I got some from Ben Franklin Craft store that were 5mm. Not all of the stores carried them. Ace Hardware had some that were 7mm last fall.

Re: Looking for very small brass screw eyes

#8

Re: Looking for very small brass screw eyes

Nick Tuzzolino

www.Meiselwoodhobby.com has some

Re: Looking for very small brass screw eyes

#9

National Brand and Ace Hardware

jake Niedling

I like National brand 217 1/2 size, they are very small brass srew eyes. I think True Value stores can order these for you. Also Ace Hardware has a very small size as well, but most stores don't carry it. I had our local store order it for me and it only took a few days. Ace Brass srew eyes No. 5029152. Eye opening is 1/8" and diameter is .047" and 7/16" long.

Re: Looking for very small brass screw eyes

#10

Dennis in Southern Oregon

Re: Looking for very small brass screw eyes

Dennis in Southern Oregon

Like Spence and Bernie, I roll my own from brass picture wire. Not only is it easy to do, but the result looks much better. I have never seen commercial screw eyes on small ornaments that did not look "clunky". The gauge of the material used to form the eyes is too large for the size of the eye, in my opinion.

Dennis

Re: Looking for very small brass screw eyes

#11

Re: Looking for very small brass screw eyes

Larry In Lima

Thanks for all of the ideas. We don't have the stores that some of you mentioned in your messages, but we used to have a Michael's (crafts). Of course, it is closed up now like so many other stores around here...

I went ahead and ordered them from McMaster (since I forgot I already even have an account with them).

I am going to sit down one of these nights while watching tv, and see if I can't make some halfway decent looking hangers out of wire. This would be a way to have whatever size I want, pretty much when I want. I like that idea too. Appreciate all of the help, Larry

Re: Looking for very small brass screw eyes

#12

Joe Fleming

Re: Looking for very small brass screw eyes

Joe Fleming

I use gold or brass colored wire too. I make a loop over a 1/4" bar and twist the wire in nice spirals. Since I typically use a cap on a hollow ornament, I put the wire through the cap and tie it in knots on the inside, like when you tie thread to form knots when sewing on a button. Then I glue the cap in place on the hollow ornament.

I have never found a screw eye that was delicate enough to look nice on an ornament. They always seem so clunky for the piece. I buy the wire at Michael's.

Joe Fleming - San Diego

Re: Looking for very small brass screw eyes

#13

Mike Stafford

Re: Looking for very small brass screw eyes

Mike Stafford

I make mine from coffee colored or natural stainless steel leader wire. Form a loop around a nail, do a double twist, trim to desired length, drill an appropriately sized hole and glue it in.

I like using the wire as it is unobtrusive and 100 pound test will usually hold up even my indelicate ornaments... :b

Re: Looking for very small brass screw eyes

#14

agree, dennis. i use 24 ga. down to 32 ga.

bob davis

.24 brass wire for regular size and .32 fqr very small ornaments.

Re: Looking for very small brass screw eyes

#15

Re: Looking for very small brass screw eyes

MMann

Didn't read the replies so don't know if anyone suggested this but the eye of a fish hook works great. You can buy a package at KMart, etc, and using wire cutters cut the eye from the hook. You can find them in "gold" color, black, silver.

Re: Looking for very small brass screw eyes

#16

Re: Looking for very small brass screw eyes

Don Orr

Our club just got an order from Benny's Woodworks. They run about $4 for 200. They are the smallest ones I have ever used. I imagine Google can help you find them.

Re: Looking for very small brass screw eyes

#17

Re: Looking for very small brass screw eyes

John Veerkamp

I use jewelry findings. You can find them in craft stores like Michaels and JoAnns. They come in several small sizes. Usually thy are a bit too long so just cut them off. drill or Poke a small hole and then a dab of Ca holds well.

Re: Looking for very small brass screw eyes

#18

Re: Looking for very small brass screw eyes

Barbara Gill

Forgive me if this is redundant I didn't read allthe responses. I found some really small ones at Michaels.

Re: Looking for very small brass screw eyes

#19

Re: Looking for very small brass screw eyes *LINK*

Bill Noce Northeast Ohio

Here's the link to Benny's Woodworks hope this helps you.


http://www.bennyswoodworks.com/hangers.html

Re: Looking for very small brass screw eyes

#21

Re: Looking for very small brass screw eyes

Larry In Lima

Wow, I definitely got a lot of help on this one - and I appreciate it!! Thanks a lot, Larry

Re: Looking for very small brass screw eyes

#22

Hobby Lobby

Tony - Memphis

I have purchased several sizes there. Some are very tiny. And if you check the paper or their web site, you can find a 40% off coupon. Might save you $.50!

Tony

Re: Looking for very small brass screw eyes

#23

Re: Looking for very small brass screw eyes

Bill Turpin in WNC mountains

This is a wholesale supply that sells retail. Only problem is the $100 minimum order. The smallest and best proportioned out there. Number 7602

http://www.axelrodco.com/detail.asp?pk=273#