Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

microwave drying

Posts

microwave drying

#1

karl jr

microwave drying

karl jr

I nuked a bowl as a test. Three 15 second cycles at a power setting of 3 (out of ten). I didn't weigh it during the process or use a moisture meter, but it was surprising how hot the bowl got in such a short amount of time. After a few swipes with a card scraper and some Watco danish oil the bowl was looking pretty good. I might do that to the rest of them.

Is it worth it to nuke a bowl a bit, to dry the surface enough to sand and apply finish?

KTK

Re: microwave drying

#2

Re: microwave drying

Keith Inscho

I have tried this a few times and it does work if you are in a hurry. You still have to go through lots of warming/cooling cycles to get it dry enough to put a finish on. Too much moisture left in the wood will cause problems with most finishes I think. I have also tried alcohol, and that works as well, but also has its share of problems. Its easier for me just to rough turn and let time do its job.

Re: microwave drying

#3

It works, but.....

Ray - Middletown, IN

use a scale and keep an accurate record of the weight loss. One minute on and 5 off worked for me, however, when the weight does not drop anymore,,,,stop. Don't do the one extra cycle to be sure. Copious amounts of smoke will flow from the microwave and the bowl will glow quite brightly.

Also don't do this when your wife is standing by to offer criti... uh,, helpful comments about the process.

DAMHIKT

Ray

Re: microwave drying

#4

karl jr

Re: microwave drying

karl jr

Keith,

thanks for the reply. I'm definetly in a hurry. Anything that can speed the process up is what I want to hear about. I've got a handle on procurement and processing, but I really haven't dealt with the phinishing phase yet ;)

Meanwhile, I've got a stack of bowls drying that need some finish work before they go out the door.

I've got nearly twenty days until my (extended) delivery date.

KTK

Re: microwave drying

#5

karl jr

It might work, but

karl jr

it might get other people in a snit. Particulary when the microwave no longer pops popcorn! :)

KTK

Re: microwave drying

#6

Old microwave in my shop

Jerry Hall

I put them in a plastic bag, get them hot to the touch and leave them sit for a while till just warm, then turn the bag inside out (dripping wet) and do it again. After a few cycles of this I may use the microwave several days as a kiln, with the light on and the door almost closed. I have an old microwave in my shop. Wouldn't do with out it for drying stuff and warming up my coffee. Anyway I can take several bowls to pretty dry within a week. I think steaming in a plastic bag cuts down on any cracking, sort of like a boiling regimen, but can't prove it.

Re: microwave drying

#7

Re: microwave drying

john lucas

Karl You didn't say how thick your bowls are. I have microwaved a lot of things but usually smaller stuff. I have done a few bowls to see how it works but it's not worth the effort for me. I dry the surface with a hair dryer. That lets me sand them. My bowls are usually 3/8" thick or so and they dry quite nicely in 2 days in the shop. Then I can do a final sanding if necessary and apply finish.

I experimented for a while with drying rough turned bowls. It works but takes too many cycles. If I was doing more than one or two I would go nuts. I would rather rough them and put them on the shelf and let nature take it's course. I can be turning something else while they dry or simply be roughing out new ones or turning the dry ones I have stored.

Alcohol or dedicated drying cabinets seem to be the way to go if your into production and in a hurry. I haven't experimented with either yet.

Re: microwave drying

#8

Dick Hines

Re: microwave drying

Dick Hines

I soak my bowls and other things in alcohol. Depending on how big the pieces are they will be stable after 30 days of so.

Re: microwave drying

#9

Re: microwave drying

matt overton

Dick, how long do you soak them? Do you just air dry, or drying cabinet for the 30 days. I assume it is just denatured alcohol.

Re: microwave drying

#10

karl jr

Re: microwave drying

karl jr

John, I'm turning these bowls to about a quarter inch, plus/minus. In the past I let them air dry, like you and others mentioned. I thought perhaps I could save some time by nuking them. However, I didn't really think that one through. I'd be standing at the microwave for days trying to dry thirty-some odd bowls. I guess I'll try a hair dryer, as you suggest. Or just be patient.

Thanks,

KTK

Re: microwave drying

#11

Re: microwave drying

bill Crommett

If you want to use an old microwave for a drying kiln just cover up most of the vent holes and the microwave will then act like a commercial kiln and let the moisture out slowly so the work piece wont crack. Power and time will vary for the individual oven. Sorry, Karl, this will not be of much help to you in your rush.

Re: microwave drying

#12

karl jr

Re: microwave drying

karl jr

I'll have to keep that in mind until a get a chance to do some research.

thanks

KTK