Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Sound Control

Posts

Sound Control

#1

Sound Control

Keith

New 3520b is going inside the house, but the wife is concerned about the noise. The room is an addition with 3 walls being exterior walls. The only equipment will be the lathe, grinder and sanding stuff. I had intended to add another layer of sheetrock, possibly over the top of 1/2" styrofoam. Will this be enough to make sound levels tolerable in the adjoining room?

Re: Sound Control

#2

Re: Sound Control

Joel

be sure to seal and sound proof the ceiling too

J

Re: Sound Control

#3

Re: Sound Control

Dick Coers

What's her concern? Afraid you won't be making enough? You know, with that kind of investment, you'd better use it everyday! I've never considered woodturning a noisy operation. Maybe for just a little bit while you knock off the corners. Now the support equipment of a dust collector and air compressor is different. Maybe you can wall them off seperately.

Re: Sound Control

#4

Re: Sound Control

Keith

Ultimately, the DC and compressor will be in a "closet" added to the outside of the house and piped in.

Re: Sound Control

#5

karl jr

Re: Sound Control

karl jr

Keith,

I would suggest separating the second layer of sheetrock from anything underneath it with furring to keep noise transmission to a minimum. You can get z-shaped strips of metal (don't remember what they're called) for this purpose.

KTK

Re: Sound Control

#6

Re: Sound Control

Nelson

Are you scared she will hear you scream when a masterpeice blows up as you throw it against the wall?

Re: Sound Control

#7

She should be used to that!

Keith

Re: Sound Control

#8

Dick Hines

Re: Sound Control

Dick Hines

The lathe will not be your racket maker. It will be the DC and compresser and the vacuum pump.

I know a guy who has his lathe in his sun room. The vacuum pump,DC and compresser are under the house. You did not even know they running. He had lights wired between the switch and the tools so he would not forget to turn them off.

Re: Sound Control

#9

Re: Sound Control

Bill Howatt

Mine is in the basement without even a finished ceiling and I don't get many comments about the lathe work and general noise but leaving the air compressor on after I leave the shop is certainly not popular. I agree with the others that it is the DC and compressor that make the most noise.

I get more negative comments about my taste in music that is playing in the shop.

Bill

Re: Sound Control

#10

Richard Allen

Re: Sound Control

Richard Allen

If you are interested in sound control then there are loads of products available to you. There is "drywall" which is designed for sound proofing. The basic process is to provide a dead air space seal up everything and don't provide a path for sound through the walls of celling. This is to say that drywall-furring strips-drywall provides a path through the furring strips.

QuietRock is one such product. There are other products.

Re: Sound Control

#11

Re: Sound Control

rjstavran

I do believe there are a couple of things to keep in mind. A previous reply mentioned sealing doors, windows, switch plates, etc. Think of sound as you would cold air entering your home - insulate. The other thing is to avoid sound transmission by contact. A second layer of sheetrock nailed over the first does very little to limit sound transmission. Your idea of a foam board between layers would be better at controlling sound.

It sounds like the wall is already there, but if you were to construct a wall, make it with 2 by 6 lumber for the bottom and top plates. Use 2 by 4 lumber for the walls but stagger them with every other stud flush with the inside or outside of the wall. The inner and outer wall surfaces only touch on the 2 by 6 lumber. I would also use fiberglass insulation in the wall cavity.

Another avenue is to make the wall soft. Covering it with carpet, heavy curtains, soft foam pads, empty egg cartons, blankets, etc. That would make it difficult to use the wall for hanging storage. and could be quite the dust magnate/collector.

Re: Sound Control

#12

Relaltive To Saw Dust, Sound Won't Be The Issue

charlie belden

If you'll be working in your living space, and you have central heat and or heat and AC, noise will be the least of your concerns. Saw dust has to be captured at the source where it is generated - or it will find its way into adjacent spaces. THAT would quickly become THE issue. And dust collection usually requires something that makes more noise than you'll ever make turning - assuming no screaming and yelling - after something goes terribly wrong ; ). Even small lathes can involve occurances that result in screaming and hollering - as well as cussing and swearing - and occasionally what might pass as clog dancing or Irish dancing.

Re: Sound Control

#13

Re: Sound Control

Don Evans

You mentioned housing the dust collector and air compressor in an add on to the house eventually.

Understand that to give this a chance to work as well as possible from a noise view point consider the following:

DO NOT let this outside building touch in any way the main structure of the house, not even a boardwalk (no matter how small, could only be 1 inch long board walk for example). Noise comes from vibration lots of time through hard mounted or attached surfaces and can transmit long way.

NOT having it attached can raise issues with home insurance policies so make sure and check that out with your agent, even then they make mistakes so take it deep enough to make sure you are covered.

Re: Sound Control

#14

Re: Sound Control

Bob Macgregor

This touches on a thought I had. The wall sound transmission suggestions are good, but I wondered if there might be some transmission of vibration through the floor? If it is wood and attached to the rest of the house, it is possible there could be some hum, buzz or rattle that gets transmitted through the wooden sound pathway (the beams) into the living space, or, if there is a crawlspace, through this space. If your addition is on concrete, particularly if there is an expansion break between it and the house, then this route of sound transmission isn't as likely.

In any case, I don't really think this would be obtrusive, certainly not compared to DC or compressor noise, but it is something to be aware of.

BOB

Re: Sound Control

#15

Thanks Everyone!

Keith