Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Eastern Hemlock?

Posts

Eastern Hemlock?

#1

Eastern Hemlock?

Bruce Newman

Eastern Hemlock - Tsuga canadensis Pinaceae

http://www.wildwnc.org/education/trees/eastern-hemlock-tsuga-canadensis-pinaceae...

Green River, NC

http://www.americanwhitewater.org/content/River/detail/id/1080/#tab-rapids

This tree is very special to me for a laundry list of reasons. Since we are losing them do to disease, I want to turn a number of pieces using this wood. It comes from a very spiritual and special place to me, Green River NC. My family originally is from there and we still have a cabin in the gorge. I spend most of my free time kayaking in there. Today, some friends and I humped out some MASSIVE logs. I am imagining the wood is fairly bland? Anyone turned any? Does it move a lot? Is it going to be tricky sanding? (hard/soft/hard layering) Anyone have any great embellishing ideas? Anyone ever tried o get it to spalt? Tried dyeing or charring?

Thanks Everyone in advance for any and all information!

Re: Eastern Hemlock?

#2

Steven Antonucci

It's an evergreen

steven antonucci

so, I'd suspect it's going to be much like pine. you can turn it, but you'll have all the same issues.

When I drop a standing dead hemlock, my work is done when the tree starts to move. Most of them explode into sawdust when they hit the ground here, but they've been dead a long time...

Steve

Re: Eastern Hemlock?

#3

Re: Eastern Hemlock?

Mac Ray

It's an OK wood...some of what we buy here in the east for framing as spruce, is really hemlock......it doesn't have a lot of character but will be worth the effort as long as you dont expect a lot of figure...doesn't have pitch like pine does,so thats a plus...........would lend itself to decoration like pyro or texturing.....use it and enjoy it...........

Re: Eastern Hemlock?

#4

Re: It's an evergreen

Bruce Newman

Hey Steve, how does pine turn? Sorry I have only turned walnut, oak, and cherry (neophyte).

Re: Eastern Hemlock?

#5

Richard Allen

Re: Eastern Hemlock?

Richard Allen

Soft, loads of sap, lots of endgrain tearout so use sharp tools with light cuts.

Makes good lumber. Framing a shed or "play house" with it would be using the wood to a good purpose.

You could panel or wainscot a room with it. Anything which will avoid the endgrain.

Endgrain can be helped by sharp tools and filling the endgrain with something that is compatible with the finish you want to use. Wax, oil, water, something to fill the spaces in the endgrain so that a sharp tool can make a clean cut.

An oil finish can yield a beautiful honey gold color. Avoid to much detail as the wood is to soft to support a lot of detail (sharp edges or lots of changes in direction).

Side grain sands glues and dyes (with an amber undertone) wonderfully.

Pens would look bland but the history would support the pens nicely.

Re: Eastern Hemlock?

#6

Steven Antonucci

soft, tears out if your tools aren't sharp

steven antonucci

and you aren't on the bevel.

It's just wood, so go get some and try it out. Worst case is you have fire wood.

S

Re: Eastern Hemlock?

#7

Brad Vietje

Re: Eastern Hemlock?

Brad Vietje

Bruce,

It's relatively soft, and it can be hard to get a clean cut when turning. There's a large difference in density between early and late growth -- in other words, the "lines" in the figure are harder and tend to cut and sand differently than the pale, softer wood in between.

Here in the Northeast, it's the most common wood for post & beam timber framing, and is usually used green. I don't like turning it, but did some experimentation texturing it with a wire wheel after green rough turning, trying to keep the wheel running with the growth rings.. The softer wood wears away to leave the raised (harder) growth rings. Can get a nice effect this way. You could also play with torching, brushing and oiling it for a tactile surface. Otherwise, cutting the logs into boards would give you a lot of flat-work options.

Safe spinning,

Brad Vietje

Newbury, VT