Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Sanding Spalted Wood

Posts

Sanding Spalted Wood

#1

Sanding Spalted Wood

Dave Gelnett

I am slowly getting better at turning the softer (spalted) woods so there is less ripping of the wood but been having problems with sanding part. I have noticed that the softer areas will almost disapear when I start to sand. So I have treated the area with different solution like CA glue or a sealer to stiffen the fibers.

The problem then is the CA glue is harder then some of the other areas and now I start to get another dip. So now there are twice as many and I think it would of been better not to try and stiffen the fibers.

It almost seems I need to match the hardnes of the wood with the solution I am using.

Any advice?

Thanks

Re: Sanding Spalted Wood

#2

Re: Sanding Spalted Wood

John Veerkamp

There are several good ways to stiffen fibers. Use a dilute coat of lacquer. It will not have the same problems of differential hardness as the CA. Another way is to soak the whole piece in a very dilute solution of PVA (white) glue and water. I think Russ's writings describe this method. It works well of soft woods. Again you won't get quite the extreme variability of the CA.

Just a couple of ideas.

Re: Sanding Spalted Wood

#3

Steven Antonucci

Skew first, hand sand later

steven antonucci

The better your cut, the less you sand. A skew is a great tool for the arsenal on spalted woods. Hand sanding slowly with the grain minimized the undulating you get with powersanding on the lathe...

S

Re: Sanding Spalted Wood

#4

Re: Sanding Spalted Wood

John Lucas

Everything I've tried changed the hardness of the wood and causes the problem you are talking about. I use a cabinet scraper to level and smooth those areas so that I can start sanding with a finer grit. Usually 220 is good. Sanding with the lathe off helps. The problem gets worse when you start with the course grits so it's beneficial to shear scrape as best you can so you can start with finer grits.

Re: Sanding Spalted Wood

#5

Re: Good tool work eliminated.....

JamieDonaldson

...most of the sanding problems, allowing less agressive sanding to distort the softer areas of your shapes. I also use lacquer diluted with a bit of acetone (5~10%?)as a sanding sealer/wood stiffener.

Re: Sanding Spalted Wood

#6

Re: Sanding Sealer

Mark Mandell - Gone Round In Jersey

Used to use thinned solvent lacquer, but after trying some waterborne sanding seal [General Finishes], I'm staying there. The waterborne raises the grain a bit so the spalted fibers stand up before they stiffen. Makes sanding them much easier. Also, change your abrasive more often; you want the sharpest fresh grit to cut, rather than rub, the fibers off.

Re: Sanding Spalted Wood

#7

Re: Mark- since the GF Sanding Sealer

JamieDonaldson

...is H2O based, about how long does drying require before it is workable?

Re: Sanding Spalted Wood

#8

Re: Mark- since the GF Sanding Sealer

Mark Mandell - Gone Round In Jersey

Light coat, dry wood, usually about 30 minutes to sandable. Humid weather (or working in the rain :D) will take longer. One gent I spoke to said to speed the drying by adding a bit of DNA, but I'm unwilling to mess with the chemistry so haven't tried that. Besides, I'm never in that much of a hurry anyway.

Re: Sanding Spalted Wood

#9

Re: How about a hair dryer?

JamieDonaldson

Re: Sanding Spalted Wood

#10

Re: Sanding Spalted Wood

George Van Beynen

Dave, Like John, I have a bunch of cabinet scrapers in different shapes by the lathe.

For sanding after scraping, I shape Dow blue Styrofoam with a Surform rasp to fit the shape of the curve to use as a sanding block. It keeps the sand paper from dipping into the softer areas.

Re: Sanding Spalted Wood

#11

30 minutes to dry in NJ?

David Walser

Mark,

If it only takes 30 minutes for the GF water-based sanding sealer to dry in NJ, I think it'd dry before you could pour it out of the can here in Arizona.