Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Delta 46-700 Long

Posts

Delta 46-700 Long

#1

Delta 46-700 Long

Don at Central Illinios

I am a problem with my Delta. Most of the time it does OK, but lately, especially Saturday something is wrong! I was roughing out a HF, and noticed some wobble. I stopped the lathe and i was cutting on one side but not the other, by mayby a 1/16". I started to take it apart to check the bearings but they seem OK. I just checked a bit ago and noticed that the head stock and tail stock to not line up properly, but yesterday, I wasn't using the tail stock. I know the lathe is fairly old and I can't find a way to get it completly apart to relace the bearings. Does anyone know of a web site with step by step instructions to replace the bearings? Any help, greatly apreciated.

Re: Delta 46-700 Long

#2

Re: Delta 46-700 Long

Sean Troy

It may not be the bearings. If you put the drive center and live center as close to tip to tip as you can and very slowly turn the hand wheel, does the drive center tip rotate around the tip of the live center or rotate off to the side of the live center tip?

Re: Delta 46-700 Long

#3

Re: Delta 46-700 Long

Don at Central Illinios

Didn't think of that. I'll check it out later tonight. If it does rotate (out of round) how do I fix it?

Re: Delta 46-700 Long

#4

JL

Re: Delta 46-700 Long

JL

I'm with Sean - it may not be your bearings. If your points aren't aligning, it can sometimes mean that your bed is "torqued" or that the headstock isn't seated correctly.

I would try reseating your headstock as a first try. Make sure that it is firm and even on your bed ways. I would then try leveling your lathe - trying to see if you can bring the drive point into alignment with the tailstock live point at full extension. I was surprised to find out that this could sometimes be the problem.

I have changed the bearings on a 46-715. Which is the later version of your machine. It isn't too bad - although a wheel puller comes in handy for pulling the spindle shaft.

Re: Delta 46-700 Long

#5

Re: Delta 46-700 Long

john lucas

Don It's been a long time since I had my Delta but I think I had problems with the headstock not sitting flat. I actually had to shim it on one corner to keep it from rocking and vibrating. As JL said check to see that all the surfaces under the headstock are clean and that it sits flat. Then check the level of the bed.

if the center point of your headstock drive center is not running true it could be the center itself. Try putting the tailstock center in the headstock and then rotate the headstock to determine if it's the center or the headstock it self.

You could have a bent spindle. Remove the headstock drive center. Clamp a pencil or piece of steel to the tool rest and push it up really close to the far side of the #2 morse taper. Watch the gap between the pencil and the side of the taper. It should not change at all. If it does then you have either a bearing problem or a bend spindle.

Re: Delta 46-700 Long

#6

Re: Delta 46-700 Long

Sean Troy

It could just mean something as simple as a dirty inside of your drive spindle. They need to be cleaned out every so often or maybe the tip of the drive spur is off just a bit. If the tip of the drive spur is slightly circling the tip of the live center it's most likely not the bearings.

Re: Delta 46-700 Long

#7

Re: Delta 46-700 Long

Don at Central Illinois

I haven't put it all back together yet, but it seems the drive center in the head stock is turning fine. I may have been some gunk on the spindle. I haven't checked yet but it may be the face plate is not seated properly. If the head stock is OK, that's about all that's left. Thanks all for pointing me in the right direction.