Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

I need some help

Posts

I need some help

#1

Steven Antonucci

I need some help

steven antonucci

Here is my dilemma. I had a sunroom with some water damage in the floor. I've been dreading the repair, so like I usually do, I start on it full force-which forces me to address the situation!

I knew that there was damage under the tile in the room, so I took all of the tile out, and when I got to the subfloor, the damage was in a 4'x6' area. I have removed almost all of the wood except these two small sections:


Both have a similar issue. When the room was added to the house, they built a deck structure, and then laid a floor on top of it. All of the sheathing is nailed through the top of the plywood, and I can't get these little nubs of plywood to come out. Short of spending the next two months with a pair of pliers pulling at it one splinter at a time, I am looking for a better idea?

No thought too outrageous. Thanks in advance.

Steven

Re: I need some help

#2

Re: I need some help

Mike Jones in Redding Ca.

It looks like a sawsall job to me. Hard to tell from the pics.

Re: I need some help

#3

Re: I need some help

Toney Robertson

First, I would remove the electric baseboard heater and get it out of the way. I assume it is electric since I don't see any pipes coming down from it.

Then like Mike said, get out your trusty recip saw and get as close to the wall as possible. Try and not get into the joists any more than necessary. You might have to use a chisel to remove some of the old plywood. Blocking between joists before relaying the plywood would really help. I know that it might be a pain to put in but IMO worth it.

Lay the new plywood. I like to use glue and screws. Use filler (Water putty is good stuff) between the old and new if necessary (and it probably will be) and bingo - new floor.

Re: I need some help

#4

Leo Cuellar

Re: I need some help

Leo Cuellar

If it were me, I might try pulverizing it with an air chisel/hammer. They are surprisingly handy for small demo jobs.

Re: I need some help

#5

Re: I need some help

ed hoxter

steve, i went thru the same ordeal a few years back in my bathroom. the fellows ahead of my post got it right. {sawsall} try to cut just the nails if possiable,not the joists. pay attention to the new height, compared to the old height level. you might need to add some rosin paper down to build up the height. {one of my problems} good luck ed

Re: I need some help

#6

JL

Other than a Sawsall...

JL

you might consider a Fein MultiMaster or equivalent. I was helping a friend do a bathroom remodel a while back. His MultiMaster made quick work of a similar situation. We had to take out the floor plywood, the drywall and a lot of other stuff to fix the results from a SERIOUS plumbing problem. Needless to say, it was a good tool to use. The price is a big drawback - but if you don't have a Sawsall already....

Re: I need some help

#7

Re: Other than a Sawsall...

Stuart Johnson

I have a Dremmel multi tool knock off. It works great and cost much less.

Re: I need some help

#8

Steven Antonucci

I thought Sawzall too

steven antonucci

Thanks for the advice. It validates what I was thinking, now I just need to wait until one of my friends brings their Sawzall or Fein Mulit thing over... I am planning on cutting the plywood closer, and then trying to undercut the nails from between the plywood and the joists.

And as a side note, there is electric running to an outlet, but the heater is forced hot water, not electric. I'm sure of that, since it's all pretty well exposed, but there's always the nagging doubt that you'll either cut something that carries water or current... Yeesh!

S

Re: I need some help

#9

Re: I need some help

bill crommett from Seneca

Steve: Start at the beginning and cure the water problem first. Then cure the ventilation problem, and then do the reconstruction.

Re: I need some help

#10

Steven Antonucci

definitely the plan...

steven antonucci

but I need to get the floor closed up again before I fall through. the issue is in the flashing to the chimney(I think) and how it connects to the sunroom. If not, it is from the cap and the water leeching through the bricks...

Either way, it's a big PITA>>>

Thanks

s

Re: I need some help

#11

Re: I thought Sawzall too

R Payne

A proper cold chisel will make short work of a dozen or 2 nails. The problem is finding a good cold chisel. I finally made my own which works much better than anything I've bought. Easy enough to do with a piece of 1/2 round tool steel (I used 1095). If memory serves (the chisel is out in the shop) I hammered to about 20 degrees, heat treated and tempered. Then ground about a 50 degree primary bevel and about 60 degree secondary.

Of course a sawz-all is more fun.

ron

Re: I need some help

#12

Re: I need some help

Doug Trembath

Me too, a metal cutting blade and a pair of pliers, looks to me. Run it over the tops of the joists..

I'd go so far as to use a crowbar, Steve, to get that old wood out. If you don't do it now, it will become much jess pleasant as time passes...

2cents, FWIW, in your interest...

Doug Trembath

Re: I need some help

#13

Re: definitely the plan...

Jeff Willaford

Some soft brick came into this area years ago. Thompson's Water Seal - -Multi Surface Sealer - in a garden sprayer every 2-3 years seems to work for water leaching thru the brick.

Re: I need some help

#14

Re: I need some help

John Scheideman

As has been suggested, you really need a MultiMax or equivalent. Dremel's is about $100 and Rockwell has one for $120 that comes with a few more items than the Dremel. Rockwell's can also be used with other brands of blades.

Those little tools are really good for certain jobs and yours is the perfect example of where they excell. Good luck.

John

Re: I need some help

#15

Steven Antonucci

This is post crowbar

steven antonucci

I simply can't get the bar in any more without damaging something I am trying to not demo...

Some of the wood was so far gone that you could have put your foot through it. Made for easy demolition, but a mess... I cut it back past all of the damage, and now I just need these two areas cleared and I am ready to repair.

I'll fix the leak after the new plywood is down, but before the new floor is laid.

S

Re: I need some help

#16

One word: Sawsall!!

Jorge Casta�eda

Re: I need some help

#17

Steve Kubien

black powder

Steve Kubien

Geez, I've been reading John Lucas too long.

Re: I need some help

#18

Re: I need some help

Scott Greaves

I would use a flush cutting trim saw. Flooring installers use them to undercut door jams and such. I have one I'd loan you if you lived around the corner. Probably easier to rent one for a few hours from a flooring supply place.

Scott.

Re: I need some help

#19

Re: I need some help

JohnKyler

Fein MultiMaster or Rockwell Sonicrafter.

Dremel is not heavy enough.

Re: I need some help

#20

Re: I need some help

Barry Irby

I agree with all the recommendations for the Sawzall. Its the closest thing I have to a light saber. A really big eraser.

I also agree about the Multimaster. I bought a Bosch rechargeable one at the Borg on impulse from the closeout table. If I had known how useful it could be I would not have gotten a battery one, but gone for the corded version. Not something I use every day, but very handy.

Re: I need some help

#21

Re: black powder

Bob Macgregor

Right. A line of thermite along the baseboard would do the job, no doubt. Steve would like a nice, new house, I'll bet.

BOB

Re: I need some help

#23

Steven Antonucci

Itching to make thermite

steven antonucci

Ever since watching Myhbusters, I've been itching to do it. The same little voice that kept me from buying a motorcycle keeps me from making thermite...

S

Re: I need some help

#24

Re: I need some help

Lee Daley

I'd reach for the multi-tool for that. That is, if my son hadn't already 'borrowed' the expensive original and 'stored' it for me in his truck. But the "Place by the Water Cartage" one although, clunky will probably get you through this project at minimal cost. Beware I don't think it comes with any blades. But all these tools are like pointing your finger and making a cut. Good luck

Re: I need some help

#25

Re: I need some help

Don Orr

How about one of those vibrating flush cutting saws like the Fein multimaster ? Cheap HF version might just do the trick.