Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Tell me about black locust

Posts

Tell me about black locust

#1

Steve Kubien

Tell me about black locust

Steve Kubien

I have the opportunity to score some black locust at no cost. The largest log is about 10" or 12" in diameter and lots are closer to 8". They're all around 12 feet long or better.

All I know about it is that it's hard as h*ll when dry and it doesn't rot in the ground. Is it so hard that it will give me grief to finish turn? What about it's ultimate colour?

My current thinking is I'll pre-drill some peppermill blanks and just true up the entry to the holes when it's dry (assuming it distorts). Perhaps some rolling pins.

Give me your thoughts and know-how. Should I bother with it knowing that there is always nice easier-to-work wood out there?

Steve

Re: Tell me about black locust

#2

Re: Tell me about black locust

John Jordan

It's not difficult to work. Cuts clean, stable, can be really pretty. Nice white sapwood, green/yellow, sometimes with streaks. Oddly enough, often has rot in the heartwood, even though it will last forever after it's cut.

John

Re: Tell me about black locust

#3

Walt Bennett

Re: Tell me about black locust

Walt Bennett

I've worked two trees I had to cut down in my front yard - both about 18" in diameter. I didn't think they were all that hard to turn - I've turned honey locust and red oak that was a lot harder. They have a nice yellowish color when done.

Re: Tell me about black locust

#4

Re: Tell me about black locust

Bill Turpin in WNC mountains

We had BL bridge support timbers in 1978 that were from 1907. Impossible to pull nails to replace the bridge top. Grain darkens with age, can be very interesting.The tree is a legume and spreads by sending out runners.

One caution: Some people are sensitve to smell of it turning. It gives my wife a headache. If no sensitivity it is worth all the effort. I would not use it for pepper grinders because of a possible reaction. BL can become a serious weed tree.

Re: Tell me about black locust

#5

Steve Kubien

Thanks guys

Steve Kubien

I was under the impression it was a bear to work when dry. Thanks for steering me straight. I'll pick up a bunch tomorrow.

Also, thanks for the heads-up about the peppermills and a possible reaction. I'll use it for other spindle work and some between-sizes faceplate work.

Anything I ought to know about drying it in a refridgerator kiln or finishing it?

Re: Tell me about black locust

#6

Re: Thanks guys

Bill Turpin in WNC mountains

Most of the BL that I have turned was already dry before I got it. I believe that it will split BADLY if dried too quickly. Fence posts in this area are installed green (while you can still get staples in it without pre-drilling). There is a local turner that recycles old, used, weathered posts and makes turning blanks for small bowls, boxes, etc. He tries to always leave some of the weathered exterior. After ~50 years the wood turns silver. BL fence posts are usually quartered or sixthed, if big enough. Split with metal wedges and BL wedges. A lot of split rail fences, still standing in this area area, are BL .Old growth BL has a very close grain similar to very old growth long leaf pine, without the resin smell.

Watch the thorns...small and sneaky, not four inches like honey L. I have seen professional lumberjacks spark their saw chains on green trees. Use plenty of oil!

Re: Tell me about black locust

#7

Aage Rendalen

Great for natural edge bowls

Aage Rendalen

I recently turned about 15 smaller (5-7 inches) natural edge bowls. It holds on to its bark very well and looks, in my opinion, very good. Over the last five years I've turned black locust from time to time, always with the same predictable result. Although logs check, the turned locust seems impervious to cracking. I've deliberately avoided a glossy finish on the bark-rimmed bowls, but the wood takes a high polish if you want it.

Re: Tell me about black locust

#8

Re: Thanks guys

John Jordan


Black Locust Vessel

John

Re: Tell me about black locust

#9

Re: Tell me about black locust

Reed Gray

Quote from the Midwest,"Black locust will wear out one fence post hole, osage orange will wear out two." As said before, it is a legume, and some people are allergic to it. Have a friend that is bothered by it when it is green, but not when it is dry. Looks better to me when it has oxidized (or patina has set in if you want to be artsy). The yellow green color doesn't sell that well for me. Also, I know the sap wood will glow under UV lights, think the sap wood does as well. It is hard, but far from the hardest wood I have turned.

robo hippy

Re: Tell me about black locust

#10

Jesper, Denmark

Re: What they said, and.......

Jesper, Denmark

It takes very nicely to finishing by sanding, leaving a hard smooth surface.

You may be surprised by insect channels inside the tree.

If you seal the ends, you can leave the logs outside forever, they do not rot.

Be careful if sawing out for planks. Strong internal tensions are common.

Re: Tell me about black locust

#11

Steve Kubien

Re: Thanks guys

Steve Kubien

Cool John, did it dry with all those ripples on the surface? Wow, I'm going to take more than I had planned! :)

Re: Tell me about black locust

#12

Steve Kubien

Re: Thanks guys

Steve Kubien

Bill, I've heard of the sparks and the need for oil. Maybe that's what made me think it was so hard. Any idea what causes the sparks?

Re: Tell me about black locust

#13

Re: Tell me about black locust

j. paul fennell

I have turned a lot of it when I lived in Massachusetts. It was very enjoyable to turn, and the heartwood also oxidizes to a wonderful honey brown color. I've seen it milled into lumber and used for cabinet work, again with that beautiful honey/brown color. Polishes very well, and makes great tool handles.

Finally, it has the highest BTU heat content of any domestic timber, including hickory, so your scraps can keep your heating costs down. Take all you can get, my friend.

Re: Tell me about black locust

#14

That's it - one of my favorites!

Pete Kekel

Re: Tell me about black locust

#15

Re: Thanks guys

Bill Turpin in WNC mountains

The only source of sparks must be parts of the moving sawchain. I guess the teeth are causing wear between adjacent parts? We have numerous 4 to 8" BL on our four acres, it makes a VERY hot fire. I cut the stumps flush with the ground so that we can mow over the top. I nick the top several times with saw to promote rotting, haha. Ten years later, the nicks are plain as day. I actually nick to reduce the impact on the riding mower in case erosin has occurred!

Re: Tell me about black locust

#16

Steve Kubien

Today I roughed out...

Steve Kubien

...a few pieces of the BL. Thanks for the encouragement guys. This stufff is pretty. Most of what I took is more suitable to spindle blanks so today I rounded out a bunch of 24" long pieces (longest my lathe will take and it gives me options later). I could have gotten some small bowl blanks but I have enough to keep me busy for now. Plus, the landowner said I could come back any time and they've got lots more to clear out (plus some black cherry).

Cheers,

Steve

Re: Tell me about black locust

#17

Keith Tompkins

Re: Tell me about black locust

Keith Tompkins

The bigger logs are often an orange color inside, very nice when finished. The orange colored wood seems to burn hotter as well. It's dust is listed in one of my books as an irritant and possible carcinogen, so wise to wear protection.