Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

cutting a gluing

Posts

cutting a gluing

#1

cutting a gluing

john lucas

I spent the day cutting and gluing and flattening all the parts for 4 bowl from board projects. I finally got everything glued together late tonight. I should be able to start turning them tomorrow.

I worked on the cupcake icing. It has a problem I didn't anticipate. The thickener speeds up the drying. It also gets so hot you can't hold onto the icing tube. Oh well back to the drawing table.

I worked on the button box also. I should be able to finish it tomorrow.

Re: cutting a gluing

#2

Re: cutting a gluing

Galen Vetterick

Working too late and you could end up with icing on your button box, buttons on the top of your cupcakes, bowl ring added to your clock, and bowl rings on your lamp bases. The day job has got to go to give you more shop time!

Is the bowl to the right going to remain with the octagonal shape rim? Looks nice from what I can see. Heck they all look great!

Re: cutting a gluing

#3

Re: cutting a gluing

john lucas

Galen I finally got to the hexagon bowl. I am going to leave the octagon edges. I think I'm also going to do a reverse bowl as a foot for that bowl so it's sort of a pedastal.

Re: cutting a gluing

#4

Re: cutting a gluing

Randy Gleckler

May I ask... what are the push pump tops in? Almost looks like epoxy cans or something..

Re: cutting a gluing

#5

Leo Cuellar

Re: cutting a gluing

Leo Cuellar

Looks like those are going to be very nice when you get them done!!!

Re: cutting a gluing

#6

While were asking

Galen Vetterick

I was not looking at the pump on the cans. Just wondering how a chipping hammer fits in with the woodworking! New texturing method? ;>)

Looking forward to seeing the posts of each of the finished pieces.

Oh, and wondering who eats the wooden cupcakes? Termites?

Re: cutting a gluing

#7

Re: cutting a gluing

john lucas

Randy That is what West System sells with the epoxy. One pump from each and you get the exact ratio you need. It works fine if you need a lot of epoxy like I do when I make the icing. However most of the time I only need a little for repairing things so I use a digital scale and a dixie cup. A little math is involved but fortunately very little. I bought the epoxy and the slow and fast hardener so I can mix whatever I need. I also purchased 3 different thickeners so I could learn their characteristics. It's been interesting. I'm going to put a call in to West Systems tomorrow to see if they can help solve my icing problem.

Re: cutting a gluing

#8

If you can't fix it then you need a bigger hammer

john lucas

As you know I'm a tool nut. I like to have the proper tool for the job. Hammers are no exception so I have plenty handy right above the workbench where they are usually needed the most. The 3rd from the left is my computer repair hammer. It's very effective.


Re: cutting a gluing

#9

Dick Hines

Re: If you can't fix it then you need a bigger ham

Dick Hines

John, that's the one I would use also.

Re: cutting a gluing

#10

Joint repair

john lucas

I'm always leary of gluing Cocobolo. I used epoxy which I've had good success before however I put some thickener in to color the epoxy. Right at the very end when I was sanding with the 600 grit one end of a piece of cocobolo came loose. I quickly put some thin CA in the joint and clamped it.

That would not be my first choice for a permanent glue but prying the joint apart might mean more damage. Flexing it slightly so I could get the thin CA in seemed the answer. However I don't trust is long term so a solution was in order.

A brass pin inserted at opposing angles on each end of the Cocobolo pieces seemed the solution. I built a jig to hold the drill bit at a precise angle and then put a stop collar on the drill bit. It worked perfect. Now I just need to insert the pins and trim them flush after the glue dries.