Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

best way to mount this log?

Posts

best way to mount this log?

#1

best way to mount this log?

ILYA Z

I found this log the other day:


I think it's white oak. The log is about 10" in diameter and 10" long. I want to turn something bowl/vase-shaped out of it using the good side of the log as the bottom and trying to avoid removing bark on the opposite side of the log or making any marks on the partially rotten inside.

What's the best way to initially mounting it on a lathe? The photo shows my first pathetic attempt at it. The top of the (future) bowl is at the headstock pressing against a piece of plywood. No glue, screws or anything. Right after I put it up like that I realized that turning the lathe on would probably be suicidal so I didn't do it.

Is there a better way? I guess one solution would be to use a faceplate. This would be OK except I would have to deal with screw holes later. Any other options?

Also, can you think of anything else I should keep in mind before or when turning it? E.g. should I be worried about the top curved "shoulders" of the log breaking off?

Thanks much!

Re: best way to mount this log?

#2

Re: best way to mount this log?

GaryG in MD

Hi Ilya,

Good score!

I saw one of these made into something nice once a long time ago, but I can't remember how it was done.

I have some suggestions:

1) Seal it up with shellac so those cracks may be retarded. (Wax would be hard to get off and will get on places you may not want it later.) Any finish will go over shellac.

2) Consider an orientation at 90 degrees (end grain). I'm not saying one is better than the other, just that you should consider both before cutting.

3) Try asking Doug Pearson -- he's good with this kind of thing -- I've seen him do hollow logs before, if not with the great "horns".

Good luck, and let us know how you do it, Gary

Re: best way to mount this log?

#3

Re: best way to mount this log?

Terry Scott

My way of going about this is to glue and screw wedges on the ply then with the tail

With webbing straps go through the void and screw down onto the ply as well

Leave the tail stock in its its current position turn on a spigot

Shaping of the bottom can be stated then as well

Then mount in the chuck bring up the tail stock and finish shaping the outside

Re: best way to mount this log?

#4

Dick Hines

Re: best way to mount this log?

Dick Hines

Not sure I have guts to turn something like this but I would love to see when it in completed.

As for holding it on the lathe, how about drilling a hole in the "face plate" and running a bolt through and adding some kind of a plate to catch the under sides of blank. Adding a lot of hot glue would help too. I think

Good luck!

Re: best way to mount this log?

#5

Re: best way to mount this log?

John Lucas

Depends on the final shape you want. I have looked at logs like this and my thoughts would be to simply turn a tenon on the tailstock end. Then I could either mount a chuck or faceplate and turn the rest. In my case I only wanted the inside and ends to stay the same. I would turn all the rest. Good luck. I'll look forward to seeing what you get out of it.

Re: best way to mount this log?

#6

Re: best way to mount this log?

Carole Valentine

Listen to Terry...he's the master at this sort of thing. A larger wood plate to allow for the straps and some strategically placed wedges should do the trick. Look through some of Terry's posts with pictures of weird mountings he's done to get some ideas.

Re: best way to mount this log?

#7

Steven Antonucci

A few different ideas

steven antonucci

If you know how big the top of the 'thing you envision' will be, you could drive screws into the bark through the backerboard that sat in the areas that you will be wasting away. This would allow you to turn your tenon, and then you could reverse it and finish the outer shape.

I think the bigger challenge will come from trying to turn the interior without ripping the tenon off. You've got a lot of wood and void interruptions going on there, and I'd probably consider removing a lot of the mass with a die grinder before cutting the inside.

S

Re: best way to mount this log?

#8

this was done similar to post bu john lucas

bob davis


Re: best way to mount this log?

#9

Re: best way to mount this log?

Doug Trembath

Ilya, I have played around with some stuff like this, and have had some luck using an extended driver which would project into the void between the curls, and press against the bottom of the void, toward the headstock. I'd first use a circle template and bandsaw the blank round, to do my best to keep the wings from running out into space due to centrifugal force. I'd also kep the lathe speed a bit lower than normal.

I turn a lot of deep vessels, and sometimes need to use the extensions to reach the bottoms when the wood has too many voids to use anything else. Picture an end grain block of wood in a good chuck, long enough to reach the bottom of the "vessel", (which could hardly hold anything with those voids), squeezing the wood between the bottom of the void and the outside of the wood supported by the tailstock. Essentially it's a drive center extended way out over the bed.

Shrinkwrap, if you don't wrap it so tightly that it deflects the wings of the turning, will help keep things together as you turn the inside, if you do.

Absolutely wonderful piece of wood! It could make a number of really interesting shapes, as well. Wish I had some!

If any of the above is unclear, email me for discussion.

Doug Trembath

Re: best way to mount this log?

#10

Re: best way to mount this log?

Doug Trembath

Sorry, Ilya, must have been a senior moment. (I'm now qualified to have them, as I will hit 60 in November!)

The extended driver projects toward the tailstock, not the headstock, pinning the work between the driver and the tailstock.

Sorry for any confusion, all...

Doug Trembath