Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

more bowl from a board

Posts

more bowl from a board

#1

more bowl from a board

John Lucas

I made 2 more to try out some of the techniques I've seen. they are challenging. On the one with stripes I tried my very best to align all the stripes perfectly while gluing up. I know the boards didn't slip. apparently I missed somehow. It's hard to see the lines with the rough edges. I'll have to try some other way of aligning them.

The other bowl was done by gluing up an 8 segmented flat board with poplar lines in between each segmented.

Re: more bowl from a board

#2

Re: more bowl from a board

bill crommett from Seneca

John: It all looks good to me. Point out where you missed the alignment, please.

Re: more bowl from a board

#3

Re: more bowl from a board

John Lucas

Bill the vertical lines in the top photo should be straight instead of stair stepped. I have a choice. Make them more offset so it looks like it's on purpose, or figure out how to make a nice smooth line. I like both but want the challenge of creating a straight or smooth line.

Re: more bowl from a board

#4

Re: more bowl from a board

bill crommett from Seneca

Thanks, John. I hadn't scrolled down far enough to see the bottom of the bowl.

Re: more bowl from a board

#5

Dick Hines

Re: more bowl from a board

Dick Hines

John, I like the first one best. The second one is a little regimented for me. I like the free style.

Re: more bowl from a board

#6

Ken Vaughan

Re: more bowl from a board

Ken Vaughan

John -- I keep thinking I see 12 segments separated by white. Must be the glasses or the screen having a magnification factor

Re: more bowl from a board

#7

Re: more bowl from a board

john lucas

Ken your right it is 12. My brain has gone into limbo again.

Re: more bowl from a board

#8

Re: more bowl from a board

Mike Rubes, Apex, NC

Hi John,

I like these a lot. I like them both, but really like the idea of the top one. Very nicely done. I love the light/dark contrasts.

Thanks for the pics,

Mike

Time to wear my own stripes again tonight in Apex, NC!!

Re: more bowl from a board

#9

Steven Antonucci

Parting tool or sawn?

steven antonucci

How do you make the rings? Do you part them or cut them on some kind of saw?

S

Re: more bowl from a board

#10

Re: Parting tool or sawn?

John Lucas

STeve I'm using a parting tool on these but you get a lot of tearout on the backside even using a thin parting tool. I make 2 cuts. About half way through with a 1/8" parting tool and then finish is off with a thin tool. You have to make the bowls thinner than I would like to get rid of the tearout. I'm doing this method because many of the turners in my club don't have a bandsaw.

I think a bandsaw is better however you do have to do the bowls by cutting half rings and then gluing the rings together. That takes longer and of course you have that central glue line.

A scroll saw is sort of a mixed blessing. You can cut the rings out without any glue lines which is good. It is slower than the bandsaw or parting tool method. Well now that I think about it maybe not. If you use the bandsaw method you have to take the time to glue each half ring together and if your glue joint isn't perfect you have to flatten the ring. with the parting tool you still have to flatten or at least sand out the torn grain that sticks up and prevents a good glue joint. The scroll saw won't cause either problem and has a thinner kerf to boot so in the long run it might turn out to be the best method.

Re: more bowl from a board

#11

Re: Parting tool or sawn?

Bill Neff

I don't have a band saw and I've wondered if you could use a jig saw to cut the circles? I believe mine will tilt over to 45 degrees. I guess I could give it a shot.

Re: more bowl from a board

#12

Re: Parting tool or sawn?

John Lucas

I think it would work. The cuts don't have to be that accurate as long as the wood overlaps to make the bowl. Your going to turn away the cut line anyway.

Re: more bowl from a board

#13

Katherine Kowalski

Re: Parting tool or sawn?

Katherine Kowalski

John,

Someone in my club has made these types of bowls using a bandsaw. However, instead of cutting them in half, he makes a single diagonal cut in each ring to start. Evidently the kerf is not a problem, and he just squeezes the rings to make a glue joint.

Another method to try...

Katherine

Re: more bowl from a board

#14

Re: Parting tool or sawn?

Charlie Drake

I've had good success with a scroll saw. With woods like walnut, sawing goes fairly quickly. I made one bowl from yellowheart-thought I would never get through all those rings but finally did and turned out well.

Re: more bowl from a board

#15

Re: Parting tool or sawn?

John Lucas

Interesting. Like doing a bandsaw box. The joint would be visible but probably not too bad.

Re: more bowl from a board

#16

Tried the scroll saw technique last night.

John Lucas

My scroll saw is marked for 45 degrees but when you tilt it that far the blade tightening knob hits the underside of the bed. I could only get to 40 degrees which would probably work but I had already drilled holes for 45. I couldn't get the blade started without breaking. I'll try another blank one of these days but will calculate the angles for something less than 45.

Re: more bowl from a board

#17

NICE! I like the first bowl. How

Rich Pearson in Mill Creek, WA

do you do the glue up to get the pattern?

Re: more bowl from a board

#18

Re: NICE! I like the first bowl. How

john lucas

Rich The first bowl is a 12 sided segmented ring with a light colored wood glued inbetween the segments. After you cut the rings apart you rotate each ring so the lines go where you want them. In this case I tried to align them so they were offset and centered between the lines on the ring below.

It is faster than making 6 segmented rings but the shape of the final piece is much more limited.

Re: more bowl from a board

#19

Leo Cuellar

A couple of failures for you...

Leo Cuellar

to consider. Impatience is one of my greatest faults. These are stacks 2 & 3. I used double sided tape instead of taking the time for a glue block. My chuck is a cheapo, but I've been monitoring comments from everyone, and believe there is a Vicmark in my future. Anyway, I thought you might like to see a couple of alternate stacks. This has a lot of potential for platters as well. I used the parting tool method for separation. My angle obviously was too steep :\

Keep up the good work John!