Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Kristen Kone

Posts

Re: Kristen Kone

#26

Re: I am totally missing something here.

Russ Fairfield

I am missing how this device can be of any use to me. I can see using the mandrel and cone for the final sanding and finishing of the outside of a vessel if that is left until after it has been totally hollowed and completed before doing that. But I do all of my sanding on the outside either before making the final finishing cuts on the inside, or before doing any hollowing.

I can also see using it to start removing the chucking spigot from the bottom, but there is a limit to how much can be removed. At some point I have to remove the tail center so I can turn and finish the bottom of the vessel, and this thing is totally usless for doing that. At that point I have to go back to the old way of doing it by leaving sufficient spigot to support the piece, removing that by hand, and and doing the final sanding and finishing on the bottom free-handed.

To me, this device has solved nothing. To those who say use this all the time - What am I missing??

Re: Kristen Kone

#27

Re: Thanks- I get a little burnishing,but it sands

Allen Neighbors

Steve, if you turn hollowforms really thin, with openings smaller than 5/8" dia, the Kirsten Kone is one of the better tools to have in your arsenal. You can make the point on the cone as small as you need, to fit the opening in your form... The only limit is the size of the rod that goes to the bottom of the form.

Re: Kristen Kone

#28

Re: Ask Art Liestman

Craig Daymon

Hey Art,

Thanks for popping out of witness protection to reply. Sorry if I blew your cover.

You put on a great demo and I learned a lot from it. Probably time I went to another to catch up on what you've been doing since.

-Craig

P.S. I also picked up a pack of Prismacolor markers after the demo, just in case you're due a commission.

Re: Kristen Kone

#29

Re: Ask Art Liestman

Wally Dickerman in Arizona

Art does even better if he has someone there to heckle him :b

Wally

Re: Kristen Kone

#30

Re: I am totally missing something here.

Allen Neighbors


Russ,

You've figured it out, I think. I use it for thin forms, to drive the rotation from the bottom, rather than the top. I turn away the tenon, and finish the bottom, except for about 1/8" nub.

This little chuck mounted sanding device is what I use to get rid of the nub. There's a small patch of velcro under that sanding disc.

Re: Kristen Kone

#31

Re: Kristen Kone

Bob Edwards

Don Pencil has a simply version of what you are looking for. He calls it a "JAMB Chuck" You make the cone to fit your project and use a sanding pad, in a chuck, fitted into the tailstock. But the price is right!!

http://www.donpencil.com/

Re: Kristen Kone

#32

Joe Fleming

Re: Kristen Kone

Joe Fleming

Yes, Oskar Kirsten invented it. He did a production run of 10 pieces for close to $100 each in the late 90s. We (SD Woodturners) finally found a local machinist that could do it for around $35. I think we sold several at cost, then raised the price to about $50. Proceeds went to the Toys for Tots program.

We had great difficulty getting the bar machined without run-out. While a bit of wobble poses no problem, too many customers asked for perfection. Our machine shop couldn't get us there, so we quit.

Neither Oskar or the SD Woodturners has a patent. I still have a few of the defective bars bouncing around in my shop, but no cones, mandrels, etc. I also have Don's jig and it works great too.

There is a pdf of Oskar's article on the SD Woodturner's website: www.sdwt.org

Joe Fleming-San Diego

Re: Kristen Kone

#33

Joe Fleming

Re: I am totally missing something here.

Joe Fleming

Allen, the issue for this approach is that the cone, when pressing on the vessel mouth, might act like a wedge and split the vessel apart. Or, if you turn natural edged vessels like Mike Jackofsky, the cone will not center properly. Or, if you turn vessels with lots of voids, you can't really apply any pressure to the rim without destroying the piece. Joe Fleming