Re: Don't forget that there is valid.....
Carole Valentine
I was just going to post that, Jamie. Pretty strong evidence too, I believe.
Knowledge You Can Build On — Est. 1998
Re: Don't forget that there is valid.....
Carole Valentine
I was just going to post that, Jamie. Pretty strong evidence too, I believe.
Re: Strobes & Arcs Turning
Keith Holt
Well it looks like I am not the only crazy one out there. I have been working with this idea for the past 6 months and have had to answer many of the questions you have been coming up with. I am now able to apply strobes to my multi-axis turning. I will be at the AAW symposium this year if you would like to get together and go over what I have found using this method. This is a very risky process and should not be taken lightly.
Safety
Bill Howatt
There are far more people on this board who will not be at the AAW symposium than will and it would be nice if you would share here the salient points of your findings, especially anything related to safety.
Thanks,
Bill
Re: Strobes & Arcs Turning
charlie belden
Keith:
Having seen your work over at WOW it's obvious that you've taken multi-axis turning well into what had prevsiously only been wood carving territory. To conceive of your pieces - and then carve them - would be quite an accomplishment. To do them utilizing multi-axis turning is pretty incredible.
Alas, probably like many here, especially on the west coast, attending AAW symposiums would hit the bank account a bit too hard, especially given the current economic times. But I'd be VERY interested in what you've discovered using a strobe with multi-axis turning. I understand that using a strobe when turning involves risk of injury. Figure if Bob Rosand can teach a blind man to turn, safety issues can be addressed and the risk reduced. So I'd very much like to "hear" what you've found. Care to share some of that here with us - with legal disclaimers of course ; )
Re: Strobes & Arcs Turning
Keith Holt
Let me make it very clear that I make no claims of being an expert in the use of a strobe or turning on multi-axis. I am just a guy that doesn�t know when to stop asking, �I wonder if�.
I will tell you what I am doing now but like most of the things I do it is constantly evolving. I ended up buying a �strobe scope� that allowed me to increase the flashes one flash at a time from 1 a second to 10,000 flashes a minute. These are commonly used at print shops to see if the ink is printing correctly on the paper. I set the lathes speed than sync the strobe. Even though I can sync the numbers of flashes to match the variable speed read out, it still does not match exactly. It doesn�t bother me and I do prefer it to be a smidge off. I generally get about 30 seconds of working time on the area I am trying cut before it moves to far out of my view. John K Jordan�s idea of having the lathe trigger the strobe is a very good one; just a bit beyond my electronic understanding.
Safety:
Craig Daymon is right about headaches, migraines, metallic taste and even epileptic seizures. I do get effected by the strobe after a prolong use so I do limit the time I use it. Placing the tube as close to the working area as I can without interfering with me then I only run the strobe for 30 seconds and generally only when I am ready to take the last few cuts to join two different plains. In addition to limiting the time of use I limit the amount of strobe by narrowing the scopes area that it with illuminate. I placed a two-foot long by 4 inches wide tube over the end of the strobe and lined the inside with aluminum foil. This tube limits the strobe to the area I am working on and gives some stability to my brain, as the strobe is only now about 20 percent of my viewing area. I also find it better to have some light in the background to lessen the strobes effect. Sorry, I do not have a candle measurement on the background light.
From the little I read they say 420 flashes a minute is the highest risk for an epileptic seizure. I am not prone to the seizure but it is something to be aware of as this number is commonly hit with the off balance turning, at least in my experience.
With the multi axis work I am playing with this technique is a huge breakthrough for me in the experiments I have been doing. I picked it up watching the show � How it�s Made� on the science channel. A fan company was using it to check the blade a full speed and the strobe stopped it dead. I thought, �I wonder if�.
If you have any more questions, comments or suggestions email me at spinner65@gmail.com.