Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Old bandsaw blades

Posts

Old bandsaw blades

#1

Old bandsaw blades

John Leonard

Hi Gang, I have 7 or 8 years of old used up bandsaw blades hanging in the shop. :b How is the best way to get rid of them? Thanks in advance. John L.

Re: Old bandsaw blades

#2

Carefully

John Lucas

If you have a scrap metal yard they will probably take them and may give you some money to boot.

Re: Old bandsaw blades

#3

Steven Antonucci

borax and a coal forge

Steven Antonucci

and a try at bladesmithing?

Pattern welding old blades might be fun...

Steve

Re: Old bandsaw blades

#4

Re: Old bandsaw blades

Dick Coers

I fold mine up as tight as I can get them, then hit the fold with a hammer. I then have straight pieces about 18" long and it's very easy to recycle. A bit like working with steel banding.

Re: Old bandsaw blades

#5

Re: Old bandsaw blades

Don Evans

What I've done is roll them back up like they were when they came, then take a large enough piece of thich cardboard box and cut it so it will fold over the blade, then tape it up with duct tape. It can then be put out with the trash.

You may want to consider cutting, with tin snips some of the wider ones like 1/2" and larger. These can be used with a scraping block to make cutters out of grinding the end of the cut blade. You will want piece about 1" to 2" long depending on your home made block. You can then use them to make crapped grooves for inlay (holly, in dark wood) etc.

Make he cutter with grinding and filing, not just grinder as stated above.

If you belong to the internet version of Fine Woodworking they have videos on this procedure. Both making the block, cutters and using them, even how to make the inlay.

Don

Re: Old bandsaw blades

#6

coiling and uncoiling

John K Jordan

>...What I've done is roll them back up like they were when they came...

One caution, if the blades are heavy be sure to wear safety glasses in case the blade gets away from you! The only time I was ever hurt by a bandsaw was a scratch when uncoiling a blade.

The big Woodmizer blades for my sawmill are especially fun to coil and uncoil. It took a bit to learn the coiling but I finally got the hang of it. To uncoil I remove the ties and throw the coil on the ground well away from me.

JKJ

Re: Old bandsaw blades

#7

Re: borax and a coal forge

R Payne

If you aren't up to trying a hand at blacksmithing you can probably find a blacksmith in your area who would love to have them. May even be willing to trade some work for them.

ron

Re: Old bandsaw blades

#8

Re: Old bandsaw blades

Texian

Probably irrelevant to this thread, but 6" lengths of used metal-cutting bandsaw blades (~1" wide) make dandy thin parting tools.

Re: Old bandsaw blades

#9

Thats funny...

Barry Irby

Thats exactly what I do. I don't have too much trouble coiling them, but uncoiling them is a differrent story. They seem like they might strike like a cobra. I take them outside and fling them out into the grass.

Re: Old bandsaw blades

#10

Re: Old bandsaw blades

Emmett Manley, Lakeland, TN

I've seen woodturners use old bandsaw blades as drying supports for small items where you want minimal contact of the finished wood with the support.

Re: Old bandsaw blades

#11

Re: Thats funny...

John Lucas

I need to make a video of the guy who sharpens my saw blades. He coils and uncoils bandsaw blades that are 5" wide. I watched him coil one into 1/3rds and then coil it again into 1/3rds. If that thing got away from you it would cut your arm off. Next time I go I'll take my camera and see if I can get a movie of him doing that.

Re: Old bandsaw blades

#12

Chuck Jones - West TN

Re: Old bandsaw blades

Chuck Jones - West TN

That's good to know. I have enough old Wood-Mizer bands for... oh, about 698 parting tools. Anybody need an extra one?

I break mine into smaller pieces and put them in a friend's scrap bin at his Tool and Die shop. It's always good to be friends with a tool and die shop.

Re: Old bandsaw blades

#13

Re: Old bandsaw blades

charlie belden

I've got a small koi pond that racoons and egrets think is a sushi bar. I finally took some old bandsaw blades, pulled into a "Y" and zip tied. Layed over the pond, teeth up, the make great "discouragers". Found fur on one - once. Haven't lost a fish since.

As for making parting tools, old bayonet saw blades work better.

Re: Old bandsaw blades

#14

Related?

Tony - Memphis

Memphis isn't really my last name! I'm a Leonard too. My dad and his bunch are from the Pensacola, FL and Foley, AL area.

Tony

Re: Old bandsaw blades

#15

Re: Related?

John Leonard

Probably not, I am from the Panhandle of Texas and my dads's family came there from arkansaw back in the early 1930s. John L.

Re: Old bandsaw blades

#16

Re: Thats funny...

John K Jordan

There are some videos on the 'net on how to coil. For the big blades I put my foot on one part against the ground (teeth away from me), hold one side of the loop in each hand, then push the sides together such that the top bends down and away (if I'm remembering correctly, don't have one in front of me right now!), forming one loop of the coil. The rest of the blade sort of "falls" into place. I tried this numerous times with spotty success until one day I "got it" and from then on it was simple.

JKJ