Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Sycamore Bowl (Round Bottom)

Posts

Sycamore Bowl (Round Bottom)

#1

Sycamore Bowl (Round Bottom)

Greg Haugen

Here's a new bowl. It's sycamore, green turned to finish, round bottomed closed form bowl. It's 4" in diameter roughly, and 4 1/2" high. It's approx. 1/8" thick and has gone oval about 1/2". Bill Luce's bowls and a couple of Jimmy Clewes' were the inspiration. Only tools used were three bowl gouges, different sizes and different grinds.


Here's another view.


What do you think?

Re: Sycamore Bowl (Round Bottom)

#2

Re: Sycamore Bowl (Round Bottom)

Tery Scott

A very pleasing shape and finish and the black background compliments it so well

Re: Sycamore Bowl (Round Bottom)

#3

Re: Sycamore Bowl (Round Bottom)

Galen Vetterick

Very nice!

Looks like it could be larger than it is.

What have you used for finish?

I am turning a sycamore urn for myself and it appear to be darker wood to start. Only piece of sycamore I have turned. I was going to use Watco oil but that can always change.

Going in the ground so not sure why I worry about it too much.

Galen

Re: Sycamore Bowl (Round Bottom)

#4

Re: Sycamore Bowl (Round Bottom)

Greg Haugen

Galen,

I used Tried and True Danish Oil. It's available through Lee Valley and Woodcraft, probably others but that's the ones I know of. I like it since it's food safe wet or dry, no thinners or driers. It doesn't darken as much as other oil finishes and does dry. It's a Satin finish, I don't like a high sheen on bowls. The key to it is thin coats. It's become my preferred finish on bowls. If I wanted a higher sheen I'd use their finish that has the wax or the resin added to it.

Re: Sycamore Bowl (Round Bottom)

#5

Ellis Walentine

About those gouges...

Ellis Walentine

Can you upload pix of the grinds you have on those gouges and tell when and how you use them in creating that shape? It's a beauty, Greg. As a proud owner of two of your bowls, I know it's as refined as it looks. How big is the flat on the bottom? (Of course, it wouldn't be flat. Is that technically a foot? Need terminology here.)

Ellis

Re: Sycamore Bowl (Round Bottom)

#6

Mike Stafford

Re: Sycamore Bowl (Round Bottom)

Mike Stafford

Very nicely done, Greg. I like bowls of this form very much and turned quite a few of them while I was learning to turn boxes with a similar form. This little bowl appears to be turned from end grain, is that the case?

Beautifully finished!

Re: Sycamore Bowl (Round Bottom)

#7

Re: About those gouges...

Greg Haugen

There's no flat, nothing to interrupt the flow of the form from the rim back around to the rim. The round bottom bowls have a nice "rock" to them that can be very captivating.

For this bowl I used three gouges. I'll list them in American sizes.

5/8" with a swept back grind at 40 degrees (top).

1/2" with a swept back grind of 50 degrees (middle).

1/2" stubby traditional grind with a shorten 60 degree bevel (bottom).


If this bowl was deeper I'd switch the 5/8" and the 1/2" swept back gouge angles. But since it was only 4 1/2" deep the 1/2" gouge worked out nicely.

All of the gouges are hand ground, not a "jigged". That's just my preference so I can easily change the angle to anything I'd like without a lot of hassle. All have a double or relief bevel to lessen the bevel contact. It also only takes a couple of seconds to "refresh the edge" or to change the angle without changing a fully ground bevel to a different angle. The 60 degree grind has less than an 1/8" inch bevel, closer to a 1/16". The other two are a little more than an 1/8" at the nose.

The steeper/sharper the grind, the higher on the form it's used. I used the 40 degree grind from the rim to the largest diameter, a little below half way. Then the 50 degree grind until a little before the bottom. Then the 60 degree (Depending on the bowl shape, this grind can vary from 60 to about 80 degrees) for the bottom. The point is to keep the bevel on the wood. As the angle that the gouge needs to be "presented" to the wood, the gouge angle needs to compensate for it. IF a bowl has a very open form one or two gouges can cut all of it appropriately. If it has a deep and narrow form or a closed form, the angles the gouge can be presented to the wood are limited so the angle changes on the gouge.

Re: Sycamore Bowl (Round Bottom)

#8

Re: Sycamore Bowl (Round Bottom)

Greg Haugen

It's actually side/face grain, that's oriented quartersawn. The medullary rays are a "surprise" when the person looks into the bowl or feels the bottom and turns it over to look at the base. I have another plan for the next one's orientation.

Thanks.

Re: Sycamore Bowl (Round Bottom)

#9

Re: Sycamore Bowl (Round Bottom)

Brian George

That is a beauty.

That's not a Calabash bowl, is it?

Re: Sycamore Bowl (Round Bottom)

#10

Re: Sycamore Bowl (Round Bottom)

Keith T

Nice form Greg. I like the smooth clean line. No finish yet?

Re: Sycamore Bowl (Round Bottom)

#11

Ellis Walentine

Thanks!

Ellis Walentine

That was a lot of good information, Greg. I will be interested to try out your "settings."

Thanks much.

Ellis

Re: Sycamore Bowl (Round Bottom)

#12

Re: Sycamore Bowl (Round Bottom)

Greg Haugen

Keith, the finish is Tried and True's Danish Oil. It's my preferred finish for bowls-if they'll be utility or just admired. Nice satin finish. It doesn't over darken the wood like some of the oil finishes.

Re: Sycamore Bowl (Round Bottom)

#13

Re: Sycamore Bowl (Round Bottom)

Greg Haugen

Brian,

Yes. It's a term that's used often with a defination that changes it seems.

Re: Sycamore Bowl (Round Bottom)

#14

Re: Sycamore Bowl (Round Bottom)

Cyril Griesbach

Greg, it's a terrific bowl. Great form and finish.

Re: Sycamore Bowl (Round Bottom)

#15

Thanks Everyone!  It means a lot.

Greg Haugen

Re: Sycamore Bowl (Round Bottom)

#16

That's a Beauty.

Don Orr

I aspire to make bowls of this high quality and style. Truly exceptional. Thanks for the inspiration.