Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

And the Academy Award for Best Turning Documentary

Posts

And the Academy Award for Best Turning Documentary

#1

Steven Antonucci

And the Academy Award for Best Turning Documentary

Steven Antonucci

As promised, I did a quick video of the hollowing system last night. It is meant to address construction, setup and use. The end gets a little bit hairy, because I actually take my life in my hands using it :-)

I apologize for the video quality, because it's very difficult to shoot with one hand while trying to narrarate and turn with the other hand without losing "the shot". There will be a couple of spots where you get a great view of the floor and the conversation wanders, but I assure you that I was not knocked out by any flying wooden handles. :-)


After using the rig to undercut and rough out, I switched to hand held tools to finish the vessel because it is much quicker. You can't just grab the right tool and cut with a system, as you have to wait to remove the cutter, change it, etc...

Hope you enjoy.

Steve

P.s. The finished vessel


Re: And the Academy Award for Best Turning Documentary

#2

Re: And the Academy Award for Best Turning Documen

John Lucas

Pretty cool. I built my first one using 3/4" steel bar, 3/4" square tubing to connect the bars together and All thread rod which goes through the tubing to bolt the rods together. I found a 3/4" hollow bar at lowes to make a connector for the boring bar. Mine looked a lot like Lyle's except there wasn't any welding. I did build a wooden secondary tool rest.

Re: And the Academy Award for Best Turning Documentary

#3

Re: And the Academy Award for Best Turning Documen

Matt Overton

Thanks Steve. A hollowing system was on my radar to buy. Not now!!!!

Re: And the Academy Award for Best Turning Documentary

#4

Steven Antonucci

If I was going to do it "sourcing" new materials

Steven Antonucci

I would do a couple of things a little different. This is a good size for a small to mid size hollowform, maybe up to 10-12" deep. A bigger platform wouldn't hurt, and I would build a deadman to connect it to the floor if I was going to do large forms.

I have other bars for it, but I would want a bigger piece of oak to use the biggest bar. The original design criteria was to spend no money to make a working prototype. A 3/4" bar is nice when you are 12" over the rest, but you are committed to a 1" hole (give or take), which is pretty big in a 6" vessel.

I like the all thread idea, but I have a forge now, and I can get welding heat :-)

Steve

Re: And the Academy Award for Best Turning Documentary

#5

Re: If I was going to do it "sourcing" new materia

Grant Wilkinson

Steve:

This is great, but can you explain why the base that is attached to your lathe is so wide? Is it to give you more angles for your approach?

Thanks much.

Re: And the Academy Award for Best Turning Documentary

#6

Steven Antonucci

That was the size of the piece of MDF :-)

Steven Antonucci

If you mean perpendicular to the ways, that's just the size I had on hand. There is a second set of mounting holes drilled in the middle to center it over the ways, but I quickly realized that I would never use the rig with the tool swung all the way to the left of the platform.

If you want to undercut, it is distinctly possible that I could get out to that right edge. It would all depend upon the size of the opening and the type of cutter on the bar. The only penalty for "bigger" is that you may eventually need the deadman to support the platform, or to double up the horizontaly members of the platform like I did on the verticals (except for the one single, where I ran out of MDF).

In short, any size box can be built, as long as it is stiff and sound enough for the types of vessels you intend to make. My rig was only made this size because of the materials I had on hand. If they have been wider, I would have made the box wider...

Steve

Re: And the Academy Award for Best Turning Documentary

#7

Re: That was the size of the piece of MDF :-)

Grant Wilkinson

Thanks much, Steve.

Re: And the Academy Award for Best Turning Documentary

#8

Re: That was the size of the piece of MDF :-)

Tom Vensel

Hi Steve , I have the same lathe as you and I was wondering if you had to turn the lathe off quickly while hollowing how do you do it standing where you must stand while opperating the equipment .

Tom Vensel in S/E Ohio

Re: And the Academy Award for Best Turning Documentary

#9

Re: And the Academy Award for Best Turning Documen

Brian George

And I thank you, also, Steve. My radar was looking closer at a hollowing sys but, am re-thinkin' it

Re: And the Academy Award for Best Turning Documentary

#10

Steven Antonucci

I use the "easy button" :-)

Steven Antonucci

I was going to wire a box to the motor with a long whip and a magnetic back when I tripped across this thing at Woodcraft. It plugs into the wall, and I plug the lathe into it.

With both switches "on", the lathe is on. Either one off, and it is off. Both off, and my kids can't accidentally push a button and start it...


It is super nice to have the ability to turn the lathe off an on from either end without repositioning anything. One of those "wish I had done it sooner things"...

Steve

Re: And the Academy Award for Best Turning Documentary

#11

Brad Vietje

Golly, Steve, I Just Gotta Ask...

Brad Vietje

What the heck is the deep-cycle battery for??? Looks like you are using it for dead weight -- or maybe getting set up to turn when the power goes out!

If it's live and charged, I think getting a cover for that little lad would be a good thing -- at least if you ever drop anything. I'm only a little bit of a klutz, but I often put too much stuff on the lathe bed... and I've knocked a few things off the lathe that could have done some real damage if they had landed on the business end of the battery. It isn't very likely today or tomorrow, but probably inevitable in the long run (in my shop).

It looks like an Interstate Battery -- they make two-piece plastic battery boxes for about $9.95, if you need one.

Safe spinning (and sparking) ;),

Brad Vietje

Newbury, VT

Re: And the Academy Award for Best Turning Documentary

#12

Steven Antonucci

Well, I couldn't get a solar powered lathe :-)

Steven Antonucci

I have a small 10' rowboat, and I'm sure not carrying the battery up from the shed in the back of the yard! I know that it was charged many moons ago, but likely needs to be connected to my Priddle Wood vaporizer sans pen :-)

It is ballast, and hasn't moved in at least 3 years, as my kids have little interest in getting out on the lake to fish anymore. Sad, but true.

S

Re: And the Academy Award for Best Turning Documentary

#13

Re: I use the "easy button" :-)

Tom Vensel

Hi Steve, Thanks for the pic of your "easy button " and the discription on using it . I have never liked the location of the switch on my 1624-44 lathe and your solution looks great .There is a rumor that Technatool is comming out with some kind of remote switch this year . Tom Vensel in S/E Ohio