Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Tool grind and usage demo

Posts

Tool grind and usage demo

#1

Tool grind and usage demo

john lucas

>I'm doing a Tool grind and usage demo at my other club on Wednesday. Do you have a grind that is unusual or an unusual way you use a tool. If so I'd like to look at those.

I will show them the different ways I use the various grinds and some of the more unusual techniques. Then I'll discuss and show the difference in radius vs flat or concave grinds on tools. I'll show the difference between the traditional British grind(just made one last night because I have reground all my bowl gouges into other shapes) and the long wing grinds that have evolved on bowl gouges and how they both have benefits.

There will of course be a discussion on skews, bedans, beading tools and using a parting tool as a skew and of course parting tools and their usage.

Re: Tool grind and usage demo

#2

Steven Antonucci

I did this at one of my clubs

Steven Antonucci

>an I stressed the importance of HONING as a way of keeping the edge up to par. After every "grinder action", I showed how to use a small diamond paddle and what the result was.

It really helps to have some wood on a tathe and do a "before cut" and an "after cut"...

S

Re: Tool grind and usage demo

#3

Don Geiger

Re: Tool grind and usage demo

Don Geiger

>Hi John:

You might consider looking at the grind Trent Bosch uses when he finishes the inside bottom of bowls. It has a very steep bevel (75 to 85 degrees) and the left side is swept back somewhat like a side ground bowl gouge and the right side has the pointed tip like is on a traditionally ground bowl gouge. I made one of these and it works great. Because it is so steep you can easily maintain bevel contact and the fulcrum point is much closer because the tool is almost perpindicular to the surface of the bowl.

He uses the opposite side of the gouge, that looks like a traditionally ground bowl gouge, to do a finishing cut on the outside of bowls and hollowforms.

He uses this tool in one of his videos so a couple of years ago I made one. I took it with me to the AAW in Portland to get him to look at it. He said what I did looked great.

Don Geiger

Re: Tool grind and usage demo

#4

Re: Tool grind and usage demo

John Lucas

>Thanks Don. I have one of those. Well actually it's mine. I needed to a steep sided bowl many years ago and reground a bowl gouge to about an 80 degree angle. It's gotten so short over the years that it almost won't reach the bottom of bowl anymore.

Now I use the Hunter tool which sort of has an 82 degree front bevel if you grind the front of the supporting metal to match the bevel on the carbide insert. Because the main body of the insert is recessed the actual cutting edge about 25 degrees so you get the advantage of a steep angle on the front bevel with the cutting edge of a very sharp angle. Absolutely great tool for doing the bottom of steep bowls, vases and even the bottom of hollow vessels. Does a good job of getting rid of the little nub.

Re: Tool grind and usage demo

#5

A comment

Bill Howatt

>I dont' have any special grind but I do have a comment.

When I have attended various presentations that at some point mention tool grinds and when and where to use them, there always seems to be a lot of confusion either on my part or that of the other attendees about just what angle or contact point/area is being talked about and why this is a good or bad thing. I find pictures, either still or video, to be often less than helpful because it may not be easy to realize the orientation of the tool due to small size or reflections.

The most useful aid I have seen is a very large wooden model of a tool.

Bill

Re: Tool grind and usage demo

#6

Re: Tool grind and usage demo

Don at Central Illinois

>Sounds interesting. Can you or John Lucas provide a photo of the grind. I'm having a problem envisionsing it? Thanks.

Re: Tool grind and usage demo

#7

Ellis Walentine

Re: Tool grind and usage demo

Ellis Walentine

>John, do us a favor and take pictures of your various grinds so I can include them in the Tool Grinds library. We haven't done much with that for quite a while, and I know there are lots of interesting grinds missing. At Brad's booth in ABQ, Cindy Drozda was talking about how she grinds her detail tools. I'd love to get some of that nuance, as well as other "grinding secrets" on our pages.

Ellis

Re: Tool grind and usage demo

#8

Re: Tool grind and usage demo

John Lucas

>Don It looks more or less like an Ellsworth grind but with a really blunt nose.

Re: Tool grind and usage demo

#9

Re: A comment

John Lucas

>Bill I agree. I have a large wooden model and also have some cutouts from plywood that look like bowls so I can show when the bevel is not rubbing. Even in a video you can't see if the bevel is rubbing. You might see the results if you get a catch. :)

Re: Tool grind and usage demo

#10

Will do.

John Lucas

Re: Tool grind and usage demo

#11

Re: Tool grind and usage demo

fgvanatta

>The best demos that I have seen involving tools are Bonnie Klien's - she has large wooden mock-ups of the tool ends so she can demonstrate such things as "riding the bevel" and the audience can see exactly what she is talking about in terms of shape, angle, etc.

You might borrow a page from her book.

Frank

Re: Tool grind and usage demo

#12

Re:Years ago I made a wooden model of........

JamieDonaldson

>....the deep flute bowl gouge about 3" in dia. and have correct sidegrind profiles on 1 end and multiple incorrect grinds on the other, highlighted in red. It also shows difference between V and U flute profiles, and I believe I credit Bonnie for the idea.

Re: Tool grind and usage demo

#13

Don Geiger

Re:Years ago I made a wooden model of........

Don Geiger

I too have a wooden model of a deep fluted bowl gouge. I made it out of a 1-1/2 diameter dowell and produced a parabolic flute very close to what I have on my Crown Ellsworth gouges. Then I built a scaled up model of an Ellsworth jig to hold it with and shaped the side-ground bevel at 60 degrees using a belt sander. Granted it does not have a hollow grind, but it was a pretty good example of a side-ground gouge.

I painted the outside white, the flute black and the bevel red. The contrasting colors view well on camera.

It has been helpful in my demos.

Don Geiger

Re: Tool grind and usage demo

#14

(Message Deleted by Poster)

charlie belden

Re: Tool grind and usage demo

#15

Face Plate + MDF Disk + PSA Sandpaper

charlie belden

Trying to sharpen a curved cutting edge skew on a 1" or narrower grinding wheel, or even on the wider Tormek wheel is kind of a PITA - and dangerous if you try to use the side of a grinding wheel. But if you screw a circle of 3'4" MDF on a face plate and stick a PSA sand paper disk on it, you can then mount it on your head stock and grind or sharpen a curved edge easily and safely. Obvious once you see it - but wasn't obvious at all 'til I saw it. And with a VS lathe it's even safer.

Re: Tool grind and usage demo

#16

Ric Taylor

Not Exactly what She Showed Me

Ric Taylor

When I took a class with Cindy, she helped me convert my straight scraper to the shape shown in your drawings. However, in addition, we put a negative rake on the top of the three cutting edges.

Ric

Re: Tool grind and usage demo

#17

Katherine Kowalski

Re: One of Cindy Drozda's Detail Tool Grinds

Katherine Kowalski

Charlie, I believe Cindy's tools are made by Henry Taylor, not Sorby. Also, there should be a 5' negative rake angle on the end and side, meeting in a perfect 45' angle. Also, the instruction in your point #1 is incorrect -- the inside (shorter) "step" is NEVER used for cutting. The sides used for cutting are the very top edge, and the ground left side edge.

Also, there should be no "relief" on the underside of the tool -- just a 60' angle on the top bevel and the side bevel. (Or maybe I'm just reading your diagram incorrectly?)

In any case, you may want to modify your diagram.

I've taken several of Cindy's classes, and this was an incredibly valuable tool to have and learn to use.

Re: Tool grind and usage demo

#18

(Message Deleted by Poster)

charlie belden

Re: Tool grind and usage demo

#19

(Message Deleted by Poster)

charlie belden