Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

TAW symposium

Posts

TAW symposium

#1

TAW symposium

john lucas

>Finally got settled in after getting back from the TAW symposium. I decided to leave before the banquet hoping the roads wouldn't freeze. It took me 2 hours to drive the 1 hour normal drive. The ice would creep up on you in unusual places so you had to keep the speed down the break extremely carefully when you hit one of those places. Lots of cars in the ditches who didn't do that.

The symposium was great. I spend most of the time watching Tania Radda. Amazing artist with lots of good motivational ideas on texture, painting and creativity.

got to see a lot of friends and that's what's really good about these things. Spent some time with Mike Hunter, Doug Thompson, Don Gieger, Pete Kekel, and woodturners from all over the south. Had a very enjoyable lunch with John K Jordan.

I picked up some good ideas and few tips along the way. Made putting up with the snow a tolerable thing.

Re: TAW symposium

#2

Don Geiger

Re: TAW symposium

Don Geiger

>Hi John:

I enjoyed visiting with you and many other turners at the symposium. I go to a lot of these around the country and, by comparison, this one was very well run. I would like to express my compliments to all that help put it together.

Also, thanks to Doug Thompson for dinner, to Ray Sandusky for taking my packages to Fed Ex and to Trent Bosch for using my Vertical Solution sharpening system in your demos.

Sincerely,

Don Geiger

Re: TAW symposium

#3

Re: TAW symposium

John K Jordan

>I had a great time. Spent too much money, as usual. I enjoyed all the sessions, especially the time with Mark St Leger's and Radda's talk about using compressed wood. Frank Penta, as usual, was both entertaining and useful. I went to his tool-making session - too bad it's not possible to catch everything with 16 different demos and 8 time slots!

I'm going to try driving back today - it is normally a 3-hour trip for me.

JKJ

Re: TAW symposium

#4

Don Geiger

Re: TAW symposium

Don Geiger

>Hi John:

I enjoyed visiting with you and many other turners at the symposium. I go to a lot of these around the country and, by comparison, this one was very well run. I would like to express my compliments to all that help put it together.

Also, thanks to Doug Thompson for dinner, to Ray Sandusky for taking my packages to Fed Ex and to Trent Bosch for using my Vertical Solution sharpening system in your demos.

Sincerely,

Don Geiger

Re: TAW symposium

#5

Re: TAW symposium *LINK*

john lucas

>Boy Must have been tired last night. Lots of spelling errors in my post. I've noticed that since I started using the computer I can't spell worth a damn anymore. What's up with that. I used to be really good at spelling.

I can't wait to get started on some new projects after the symposium. Symposiums are really good at 2 things. Making new friends, especially ones you talk to on the net but never meet, and inspiring you to get out there and produce some new work.

I've had a piece on the drawing board since before I moved to the new house. It got put on the back burner due to some design issues and the ability of wood to not bend like I needed. I've been reading about comp wood ever since I saw Tania Radda's piece on the back cover of Finewoodworking and then again on American Woodturner. I researched the comp wood but it was expensive and I wasn't sure it would do what I wanted. Now I know it probably will. At least sure enough to invest in a pack and and see.

Here's Tania's website if you want to see her work.

http://www.taniaradda.com/

Below is the site where you can buy the comp wood.


http://www.flutedbeams.com/

Re: TAW symposium

#6

Re: TAW symposium

Doug Thompson near Cleveland

>I finally made it back last night about 3:15am, the roads were snow covered and slick in TN but KY and Ohio were clear. I really enjoy this symposium, the club, the way it's run plus the quality demonstrators that they bring in every single year... to this club I need to say another symposium well done. This was the first time I met Tania Radda and watched a bit of her demo's... I was very impressed by her work and knowledge. It was good to finally have time to talk with Don Geiger.

I can't wait for nest year next year... Thanks everyone.

Re: TAW symposium

#7

Another Great Event......

jake Niedling

>I also enjoyed this event and all four of the demostrators. Like John K Jordan, wished I could have seen all of the rotations. TAW does a great job. Look forward to this event every year. Y'all should have been there. The drive back to Knoxville, Tn was not bad on Today.