Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Nova 3000 - headstock pulley removal?

Posts

Nova 3000 - headstock pulley removal?

#1

Nova 3000 - headstock pulley removal?

Henry (Raleigh NC)

>I have a Nova 3000 lathe and have already appreciated your assistance in remounting the pulley set on the motor. Now I find that I want to pull the headstock pulley set. Here's why.

When I remove the drive belt and spin the headstock by hand there is a definite point at which there is a grab - a stopping point. This a mechanical stoppage that is fairly easy to overcome; even spinning it by hand quickly it will make it past this point. However it sounds like a grinding action that well, just doesn't sound right.

I have accessed the pulley set once the cover has been removed; I see a small key on the drive shaft and on the pulley set. I have removed the set screw on that key and now want to remove the pulley and find out what is grinding there. How do I do this? It is a 6 or 7 step pulley set that is covered on three sides by the headstock housing and the base. The end is now open because I have removed the cover, and the side where the motor pulley set was is the 'open' 4th side.

How do remove that key? How do I remove the pulley?

I do not feel any play in the bearings (I assume there are bearings there), and the grinding almost makes the (Aluminum?) pulleys sing (resonate) when the rotation by hand is at the right speed. That makes me fairly certain there is something grinding in/on that pulley.

The key is in place - I was able to move it down the shaft a bit when I pushed on it. So the key is in there and is holding the pulley in place. There is no play or slippage between the shaft and the pulley.

I want to pull off the pulley set because it seems like there is something in there causing that binding/grinding.

I'll have another look at it tonight, but I'm not sure what I am going to try.

Henry

(note - also posted at NCWoodworker.net)

Re: Nova 3000 - headstock pulley removal?

#2

Re: Nova 3000 - headstock pulley removal?

david

>It has been several years since I sold my Nova 3000 to a fellow club member, but I recall experiencing a noisy racket from the headstock area (concerned that it might have been bearings) but it turned out to be a set screw at the bottom of one of the pulleys. This was approximately in the middle of the stepped pulleys, and tightening the set screw solved the noise problem. You mentioned a set screw at a key, which I assume to be at the end of the drive shaft, so perhaps this set screw may have gone unnoticed. Hope it works out for you.

David

Re: Nova 3000 - headstock pulley removal?

#3

Re: Nova 3000 - headstock pulley removal?

Walter Ahlgrim

>This lathe has a tendency for the pulley to shift and rub the head stock.

Often there are 2 set screws one under the other to prevent the lower screw from loosening.

Look for a second screw.

If the set screw raised a burr on the shaft it could be difficult to remove the pulley.

Walta

Re: Nova 3000 - headstock pulley removal?

#4

Re: Nova 3000 - headstock pulley removal?

john lucas

>Ditto what the others have said It's probably a loose set screw. Loosen it further and align the pulley so the belt tracks true, then tighten the set screws and see if the noise goes away.

However if you need to remove it the burr raised is a problem. Take a drill bit that just barely fits in the hole. Drill very lightly, just enough to remove the burr. Then pull the pulley off.

Re: Nova 3000 - headstock pulley removal?

#5

Steven Antonucci

And don't use Loctite on the shaft!

steve antonucci

>It's the pulley clattering against the spindle lock/index pin. If you loosen the set screw and realign and tighten, you'll be fine. You don't need to remve the pulley.

steve

Re: Nova 3000 - headstock pulley removal?

#6

Re: And don't use Loctite on the shaft!

don lewonczyk

>It sounds like your pulley maybe to far in on the spindle shaft, to close to the headstock. The pulley may not be perfectly flat, face side, and maybe rubbing the headstock at that one point. As the others have said about the set screws it maybe a combination of one or two things. DonL

Re: Nova 3000 - headstock pulley removal?

#7

Update: Nova 3000 - headstock pulley removal

Henry (Raleigh NC)

>I suspect that Steve and Don are right about the cause of the binding/grinding noise in the headstock assembly. They postulated that the pulley set is too far on the shaft and therefore at one point is rubbing on the case/housing. That fits with the sound and feel of the binding.

In trying to diagnose this, I have been able to remove the set screw and the key fairly easily. The headstock pulley is however resisting any easy movement along the shaft.

This is similar to the motor pulley and drive shaft case. When I need to realign the motor pulley set it too was frozen onto the shaft (after removal of key and setscrew). In that case wooden wedges eventually broke it free. In this case (the headstock pulleys) the resistance has not been futile; I have been only able to move it about 3/4" along the shaft, but not easily. It is not yet free from the shaft.

Is there a proper or appropriate way to free this pulley set? Is there a tool to accomplish this?

Thanks, Henry