Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

How do you hold a ...

Posts

How do you hold a ...

#1

How do you hold a ...

Ed Moore

>3/16" square bit in a chuck with pin jaws? I need to put tenons on square tool bits for hollowing tools I am making for my ornaments class at John C Campbell Folk School in November. Since the bits are too small to be held by the chuck I put 4 cut-offs of 1/4" round steel on masking tape and put them inside the chuck with the bit at the center. Effectively, you are holding a square with circles on each side. The 1/4" rod pieces are held by the grooves in the jaws and the bit is centered nicely.

With the lathe reversed and slowed, I use an air cut-off tool to shape the tenon. Before I turn the lathe on I smooth each of the four edges a little with the cut-off to make the process a little less bumpy.

When I get the tools completed I'll post a picture of the set.

Note: We have some places left in the class and would welcome a couple more.


img

Re: How do you hold a ...

#2

alternate solution

Jim Pugh

>Another way to do what you need is to get a drill bit that is sized close to the dimension of the tool bit across diagonal corners. You may still need to break the edges of the tool bit a shade. A set screw will hold the bit but it. What I have done and it works fine for me. It also allows one to slide the bit in/out as desired.

Re: How do you hold a ...

#3

Steven Antonucci

I don't understand what you are trying to do?

steve antonucci

>I looked at it twice and I don't understand what you are trying to do? I understand that you are making the holding capacity of your chuck smaller to hold a square bit, but you lost me after that...

perhaps a picture of the finished product would help?

Steve

Re: How do you hold a ...

#4

Putting a 1/8" round tenon ...

Ed Moore in SW VA

>on a 3/16" square tool bit.

The bit is not glued in the shank.

Most things to hold a small diameter piece have three jaws, which makes it awkward. Using the cut-offs provides a way to hold the small square tool bit.

Ed


img

Re: How do you hold a ...

#5

Steven Antonucci

I just approximate them on the grinder

steve antonucci

>If I am holding them with a set screw, I don't fuss that much. I knock off the corners and make the holes a little bigger. screw holds against the small flat.

Or glue em.

How are you keeping them in?

steve

P.S. Ellsworth has a small wooden jig that he uses on his grinder that spins against the rotating wheel- he was making tools for Crafts Supplies and had an assembly line mentality to speed things up. If I recall correctly, he needed to make 60 tools that weekend, which he did with very little bother...

Re: How do you hold a ...

#6

I plan to use ...

Ed Moore in SW VA

>JB-Weld or epoxy to hold them in. I also have some metal filler (aluminum) that might work. I'll have to try it out first.

Ed

Re: How do you hold a ...

#7

Jacobs Chuck?..

jwoodwright

>Ed,

How about using the Jacobs chuck in your lathe or on the drill press?

Penn State has a live Jacobs chuck they use in the tailstock. This would be great to hand hold at the grinder, the chuck would spin and you would get a more concentric grind... John

Re: How do you hold a ...

#8

Re: Jacobs Chuck?..

Barry Turner

>I think Ed was trying to say that it's hard to hold something square in a 3-jaw chuck, which a Jacobs chuck is.

Re: How do you hold a ...

#9

Re: How do you hold a ...

Barry Irby

>Why not just make a a little block you can chuck in the four jaw chuck with a 3/16" square hole? It could be a jamb chuck or you could make it a collet so that the pressure from the chuck would close it.

Re: How do you hold a ...

#10

Barry, I was about to make ...

Ed Moore in SW VA

>such a device when I saw the cut-offs of the 1/4" round steel. Actually, since the cut-offs are held in place by masking tape my system works pretty well. Another idea would be to use a little CA glue to secure the cut-offs to the jaws.

Ed

Re: How do you hold a ...

#11

Re: Barry, I was about to make ...

Barry Irby------WebKitFormBoundaryooeciKESVDEAQ+9S

>You did what I would have done. My thought process is "How can I do this with the stuff at hand?" Just glad you weren't eating a cheese sandwich at the moment.

I probably would have chucked a little piece of wood about 3/4" square, drilled a hole a little over 3/16 with a Jacobs chuck in the tail stock and heated a piece of the 3/16 stock and "Burned" it in.

Re: How do you hold a ...

#12

Re: How do you hold a ...

Texian

>You could make a jaw set from some rusty, scrap angle iron like this one, made to hold some small square blanks for finial practice.


img

Re: How do you hold a ...

#13

Dick Hines

Re: Barry, I was about to make ...

Dick Hines

>I would just glue them into the tool with thick CA, ED