Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

McNaughton coring system

Posts

Re: McNaughton coring system

#26

Re: straight cutter usage ?

Fog Tanner

>I have one of the straight cutters and that is what I use it for. When I make outflowing bowls, I core a cone or cones using the straight cutter. You can also use it to core from the headstock side, where you would need the other set of curved knives to do that. I have also used it as a parting toll on occasion.

Fog

Re: McNaughton coring system

#27

Re: McNaughton coring system

Barry Irby

>John, This is hard to explain, but I think I have it correct. If you want to get the maximum number of cores out of a blank, then the knives must be as thin as practical and cut the narrowest kerf possible. Once you start shaving the walls off the kerf, making it wider to allow for the knife to enter without burning or wedging in the kerf, you are cutting away the wood you wanted to save by coring to start with.

The only path your curved knife can take and follow into its own kerf without rubbing or burning is an arc of a circle. The knife can not follow in an oval or eclipse. (The one exception I can think of is a cone cut with a straight knife.)

This does not mean your bowls must be a section of a sphere. They can be, but Don't have to be. By changing where you start, you could easily cut a shape like a football or a vase, but the path the knife takes is still a segment of a circle.

You can cut away the wood you would have wallowed out after you pull out the core.

Re: McNaughton coring system

#28

Dick Hines

Re: welcome to the best and most frustrating tool

Dick Hines

>John, I have the large set and use quite often. When ever i get big pieces of wood or something really special I will core out 2-3 bowls. I have used the stright tool for vases and some bowls that will have small bottoms and a wide rim.

If you want to see how easy the system is watch Bill Grumbine use the system. He core useing only 2 fingers to show how easy it is. Of course Bill is some what larger than the average bear.

Re: McNaughton coring system

#29

Re: straight cutter usage ?

Bill Howatt

>Can't remember exactly what I was doing but it sure came in handy one day as a long parting tool.

Bill

Re: McNaughton coring system

#30

Bill using 2 fingers is like me using a leg :)

john lucas

>

Re: McNaughton coring system

#31

Explains system very well, get it!

Bill Howatt

>

Re: McNaughton coring system

#32

Dick Hines

Re: Bill using 2 fingers is like me using a leg :)

Dick Hines

>I did say he was biger than the average bear. He did not seem to be under strain though. I watched him core 3 bowls in a blink of an eye. He gave some good advice on how to use the coreing system that has made it easier on my tools, lathe and me.

Re: McNaughton coring system

#33

Steven Antonucci

I've done it one handed too...

steve antonucci

>And I've also torn bowls off the chuck within the blink of an eye. In a great many cases, I think it's a matter of the shavings not ejecting and getting bound in the kerf. It's frustrating to do one perfectly, and the next one is an exercise in terror...

Someday...

Steve

P.S. don't ask me how to set it up for a guided cut! I always end up deep...

Re: McNaughton coring system

#34

Re: straight cutter usage ?

robo hippy

>The straight cutter is a long parting tool. Mostly I will use it when there is a crack that I want to turn out, and it is more convenient to cut it out rather than turn it out. You can also turn a cylinder and part off sections for plates.

robo hippy

Re: McNaughton coring system

#35

Re: straight cutter usage ?

john lucas

>I was wondering about turning a cylinder and then using the curved bars to sort of core out a series of bowls all the same size. I'm not sure how you would support a turning that long. Put it on a faceplate and then use the steady rest to support just behind the cut.

Re: McNaughton coring system

#36

Re: straight cutter usage ?

robo hippy

>I did it once. I turned a cylinder about 8 inches long, and ended up with 9 bowls. When using the straight blade or the flat curved blade, you can put the tailstock up against the wood. I attach to the headstock with a recess drilled into the top with a big forstner bit, and expand the chuck into that. Not nearly as fast as cutting out the blanks on a big bandsaw and doing them individually, but it does save a lot of wood.

robo hippy