Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Best type of fasteners for faceplate?

Posts

Best type of fasteners for faceplate?

#1

Best type of fasteners for faceplate?

david

>Yes, we are talking about screws here. Getting tired of having to dig out screw threads where the heads are sheared off. Perhaps it doesn't help that I use an impact driver to fasten the faceplate to a turning blank. I also do not pre-drill except on notoriously hard woods. Have tried sheet metal screws and deck screws, but from the local Ace Hardware the shank size available is not very thick. The break-off point is usually just below the head. If I have trouble driving in the screw, I know that pre-drilling is warranted; but the break usually occurs when trying to remove the screws. The only way I have been able to remove the headless screw is to dig around the shaft to minimize the amount of thread in the wood and be able to get a vise-grip plier on it. See in the McFeeley's catalog where I can get some #12 and #14. What do you use and/or recommend?

Re: Best type of fasteners for faceplate?

#2

Re: Best type of fasteners for faceplate?

Steven Kubien

>#12 or #14 are recommended by one of the biggest proponents of faceplate use, Lyle Jamieson. Since my time with him in February of 2008, that is all I have used and never had a break-off. Lyle also loves his impact driver so I doubt that is your problem.

Good luck,

Steve Kubien

P.S. I recently saw in one of the catalogues that someone is offereing a drill bit specifically to drill/grind/mulch headless screws. This is not your typicaly extraction bit. More of an extinction bit! Sorry I can't remember where I saw it but if I do, I post it.

Re: Best type of fasteners for faceplate?

#3

Re: Best type of fasteners for faceplate?

Ray Binnicker

>I've used the screws designed to be used with the "Kreg" pocket joint jig. I've had good luck with them, so far.

Ray Binnicker

Re: Best type of fasteners for faceplate?

#4

The biggest, fatest

Jorge Castaneda~Downeast Maine

>screw you can fit in, at least a #12 steel wood screw, note that real wood screws, have a smooth shaft between the flat head and the threads, if it has threads all the way to the head is a sheet metal screw, guaranteed to loose its head. I my local hardware, the steel screws are made out of pot metal, read poop, so I go for the stainless steel ones.

You may have to pre drill, I use a tapered drill bit.

$0.02

Jorge

Re: Best type of fasteners for faceplate?

#5

Re: Best type of fasteners for faceplate?

David Walser

>I found some #12 hex head sheet metal screws at the local borg for use with my faceplates. (I had been looking for square drive screws but could not find any at the borg.) The work well and, so far, I've not broken one off. But, then, I always pre-drill.

Re: Best type of fasteners for faceplate?

#6

pocket screws...me too

Thad

>

Re: Best type of fasteners for faceplate?

#7

Roger Dunn

Re: Best type of fasteners for faceplate?

Roger Dunn

>I use #14 sheet metal screw either countersunk or pan head depending on the faceplate holes. Remember the old Norm trick to wax or oil the screws before you drive them - hence - no snap offs. But pre-drilling with tapered bits works without wax and oil.

Re: Best type of fasteners for faceplate?

#8

Re: Best type of fasteners for faceplate?

steve worcester

>If they will fit your faceplate, the best I have found are Simpson Strong Drive woodscrews (1/4"x1.5"). They are made for attaching plates to fences. They have a 3/8" hex head (I think),are hardened and you won't need to predrill in hard woods. I predrill in glue blocks though. They fit perfect in the Best Wood Tools faceplates. I use a cordless impact driver for them.

Google Simpsons SDS. I get them at Home Depot, but in qtys of 50 they are about $25.

Re: Best type of fasteners for faceplate?

#9

Dick Hines

Re: Best type of fasteners for faceplate?

Dick Hines

>When I use a face plate I use self tapping sheet metal screws. I run them up with a nut driver in my drill.

Re: Best type of fasteners for faceplate?

#10

Steven Antonucci

I use coated Concrete screws

Steve antonucci

>They have a really aggressive thread, are stronger than dirt, and wide enough to not wobble in the holes in my faceplate. If you accidentally hit them with a turning tool, you will be resharpening...

Steve

p.s. the ones I use also have square drive heads, which make them easy to drive and remove...

Re: Best type of fasteners for faceplate?

#11

Re: Best type of fasteners for faceplate?

Carole Valentine

>Same here, Dick

Re: Best type of fasteners for faceplate?

#12

Brian McKearney

Re: I use coated Concrete screws

Brian McKearney

>I use #12 Sheet Metal screws (2") - my local hardware store carries these with square drive and I have never broken one off. I drive with a Milwaukee decking driver and no pre-drilling. Once the square drive hole starts to round over, I know that it's time to toss that screw and replace with a new one.

Re: Best type of fasteners for faceplate?

#13

Spax screws

keith zimmerman, Normal IL

>

Re: Best type of fasteners for faceplate?

#14

Re: Best type of fasteners for faceplate?

John Jordan

>SPAX 12x1-1/4" n/m

Re: Best type of fasteners for faceplate?

#15

Thanks for the responses!

david------WebKitFormBoundarylRgnhGioIdOlFg+1

>BTW, Jorge, I have heard that the tensile strength of stainless steel is less than that of regular steel screw metal. Have yet to try the Spax screw, but am seriously going to look at coated concrete screws. Probably try them both!

Re: Best type of fasteners for faceplate?

#16

Re: Best type of fasteners for faceplate?

jim miles - Charlote NC

>In construction biz - put in a couple 100,000 screws, Do all my turning on faceplate & waste blocks, Some observations for faceplates: Stay away from drywall and deck screws they are too brittle, stainless steel is much weaker than the average screw, throw out slotted or Phillips heads, hex head or square drive much better, other comments in thread agree with my eperience: fatter size, pan head, use bigger number of shorter screws. The problem I have with breaking is in green wood, especially if left for a few days. Extract by drilling holes beside broken screw. Lowe's is starting to carry some new types that work well for faceplates.

Re: Best type of fasteners for faceplate?

#17

Re: I use coated Concrete screws

Don Orr

>Me too when I use faceplates. I get the Tapcon brand at the local Borg.

Re: Best type of fasteners for faceplate?

#18

Re: Best type of fasteners for faceplate?

Tom Vensel

>When I turn a segmented urn or bowl I always attach the waste block to the faceplate with 1/4" lag bolts . I always predrill the attachment holes and usually lube the bolts with soap .

Tom in S/E Ohio

Re: Best type of fasteners for faceplate?

#19

Re: Best type of fasteners for faceplate?

eliot d------WebKitFormBoundaryu+MBDi+0MX0Pf5O9---

>John, I just ordered 500 of these. Thanks! I've not had any trouble with sheet metal screws, but I am taking your advice.