Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

At What Speeds Do You Turn?.....

Posts

Re: At What Speeds Do You Turn?.....

#26

Re: At What Speeds Do You Turn?.....

Carole Valentine

>Seems like I am always saying this, but "It just depends". I turn everywhere from 500 to 3000. The larger or more unstable the piece the slower I turn. The larger the piece, the higher the perimeter speed. When I am turning a natural edge, I find that speed (within reason) helps. Yes, if you catch and blow it up, it's going to put out pieces at higher velocity (all the more reason to wear safety gear and stay out of the line of fire), but I really feel that there is less chance of a catch at higher speeds. Your tool does not have as much opportunity to "dip" into the air spaces. On regular bowls and such, slow speeds are frustrating to me...I always have to tell myself to slow the tool down. It's harder for me to "dance" smoothly with low lathe speeds. On balanced, solid pieces up to 10" I may run up to 2400. But there are always exceptions...it just depends. One reason why I love my VS lathe!

Re: At What Speeds Do You Turn?.....

#27

Re: At What Speeds Do You Turn?.....

Al Neighbors

>I turn at faster speeds than a lot of turners, I guess. I am a shaky person... benign familial tremor... therefore, faster speeds help me to make better cuts.

Out of balance, I keep it slower 'til the vibration settles down a mite. Most other times I'm going faster than recommended. Like John L, I try to stay out of the line of fire, but sometimes I just can't. My glasses are bullet proof, and I wear a good face shield, but that's about it.

My 1640 won't get as fast as my little vic... wish it would.

I sand at about 1000 rpm by hand, and with my inertia sanders, about 13-1500 quite a bit.

When my pens are round, I turn them about 2200 rpm.

Re: At What Speeds Do You Turn?.....

#28

Re: At What Speeds Do You Turn?.....

RonZ

>I usually do most of my turning on my Vicmarcs, for between centers, at full speed, 3000rpm. That includes boxes, goblets, etc..For bowls I turn as fast as is stable and safe. For my students, I start them off slow and when I see that they have learned to hold the tool right I turn up the speed. They then learn that you can cut better at higher speeds.

Re: At What Speeds Do You Turn?.....

#29

Re: At What Speeds Do You Turn?.....

Don Orr

>I guess I'm with most of the others so far. Slowish when roughing an unbalanced blank, faster when it gets balanced out. I have noticed that I have been working my way up to more RPM's lately. I'm not a pro or anywhere as experienced as most here, so I'm not in that much of a hurry. I don't usually go much above 1500 for most things. I probably should go higher on spindle oriented work though.

Re: At What Speeds Do You Turn?.....

#30

Brad Vietje

Re: Good question

Brad Vietje

>Interesting question.

I turn faster than I used to, but not like Steve. I usually turn as fast as I can spin the piece w/out vibration, and with variable speed that's a lot easier.

Doug Thompson also raises a good point, though, about safety. We should all keep in mind that for solid wood, a slower tool advance is equivalent to a higher turning speed. With experience, we learn to make the graceful arcs and curves we're shooting for with a lighter touch on the tools, and a slower advance. On natural edge work, or pieces with voids, I like to go as fast as I can without fear of the thing flying apart, to lessen the time interval between wood and air.

I think beginners should go slower, and more experienced turners faster. Before turning up the speed very far, I also take a few very fine cuts to smooth the surface and look very carefully for any cracks that could cause trouble. Beginners often don't get a clean enough cut for this visual inspection to reveal very much, so this develops with experience, better tool handling, and with a better feel for sharpening tools.

Safe spinning,

Brad Vietje

Newbury, VT

Re: At What Speeds Do You Turn?.....

#31

Re: I'm A Bit Surprised.....

Stephen Mushinski

>Early in my learning I was whacked not once but twice by the same bowl. A few things I learned:

1) Do not use the gouge with the flute pointing straight up on the rim.

2) Do not bottom the foot to the bottom in the oneway jaws.

3) Wear a face shield.

4) Stand off to the side if possible.

I still have the broken purple heart bowl I was turning as a reminder. I have not pulled anything out of the jaws for years but I still try to stand out of the way of fire as I did not like the bowl bouncing off my forehead.