Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Wood handles for Thompson lathe tools

Posts

Re: Wood handles for Thompson lathe tools

#26

Re: Burn them in - Burn say who say what?

john lucas

>I've done that many times. It works well. If you are worried about overheating a tool (not a problem with HSS but high carbon steel could be damaged) then simply put a heat sink of some sort around the blade. You can use a wet towel or vice grips. For round tangs I just drill the hole a little undersize. If it's a tapered tang I drill a few holes smaller than the tang and then heat and drive it in.

Re: Wood handles for Thompson lathe tools

#27

I'll second that!

Dominic in Buck's County PA

>That gouge was a real hoot to take for a ride! It could hog out material and the mass made it a natural for shear scraping. I just loved the way the long handle gave me all that leverage.

Re: Wood handles for Thompson lathe tools

#28

Bill, I'm working on them...

Doug Thompson near Cleveland

>

Re: Wood handles for Thompson lathe tools

#29

Re: Wood handles for Thompson lathe tools

Doug Thompson near Cleveland

>Looks Good! The Vari-grind leg setting is on the sharpening guide, place your vari-grind on the full size picture... set it then adjust the nose angle. My grinding wheel won't be the same diameter as yours but it should be close.

Have fun!

Re: Wood handles for Thompson lathe tools

#30

Re: Burn them in - Burn say who say what?

nick

>Also, as Doug Thompson pointed out to me, the tempering temperature of A11 steel is 1100 degrees, a dull red glow. Just don't heat the tang that hot and you'll be fine.

Re: Wood handles for Thompson lathe tools

#31

Re: Burn them in - Burn say who say what?

Ron in Drums PA

>I used the old fashioned way also, works well. I just wanted to say that glue isn't irreversible.

Just heat up the metal and the glue will get soft making it easy to remove the tool from the handle.

Re: Wood handles for Thompson lathe tools

#32

Re:Burn say who say what? Whew!

Ray Carson, Lawrenceville, NJ

>You all had me scared there for a minute. Thanks for explaining the process. Seems like it would work well. I don't like the idea of heating cutting tools though. I wouldn't want to ruin all of Doug's hard work in making a fine tool, despite what has been said here. I read the post about Doug Thompsons's comments but still would prefer gluing or some other way. Too many other options if you know what I mean.

Thanks again gang. Happy turning. :-)

Ray

Re: Wood handles for Thompson lathe tools

#33

Speaking of shanks

Doug Thompson near Cleveland

>I turn the shanks down on a $399 CNC lathe, it's 15 years old built for the Valenite Corp then was sold off when a plant shutdown. Once in a while I get chatter so a new insert normally cures the problem... well not tonight. I ended up tearing the entire carriage apart, checked for loose screws, adjusted the balls screws on the X & Y axis and still had problems. The last thing I checked was the spindle, with a indicator on the chuck I pushed and pulled... hummm it read .0025 this reading should be .001 It ashame that 5 min. adjustment took 3 hours to find... LoL

I'm in the process of buying another mill and lathe which should increase production about 30% then I won't have to stop to make repairs.

Re: Wood handles for Thompson lathe tools

#34

Agree 100.1%

Bill Howatt

>

Re: Wood handles for Thompson lathe tools

#35

Re: Wood handles for Thompson lathe tools

Thanks!

>Drill the hole deep, then drill and tap for 1/4 -20 set screws. The wood will thread just like metal, and you can keep the length of the gouge the same.

John

Re: Wood handles for Thompson lathe tools

#36

Re: Wood handles for Thompson lathe tools

john lucas

>I do the same but I put some thin CA in the holes after I've tapped them and then run the tap down one more time. This hardens the threads and makes them last longer.