Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

tools for turning finials

Posts

Re: tools for turning finials

#26

Brad Vietje

Re: tools for turning finials-Wow!

Brad Vietje

>Hi Carole,

Hope it's OK to chime in late with another thought...

1. I'm really picky about finials. I share Wally's thoughts (who wouldn't???) that many finials are too clunky, and are steps in an evolution toward more delicate -- and I would say more confident, finials. I'd also second (third...) Keith's suggestion of a sketchbook for shapes and designs.

2. Part of my picky-ness is that I strongly prefer finials that have an overall taper from one end to the other. That is, I don't like a larger element, then a smaller ones, then back to larger, or "heavier" elements. I like 'em best if all the major feature elements are progressively smaller from base to tip.

3. LONG BEVELS. I use a skew to rough in the tapered shape of the finial, and to make some of the deeper cuts and larger beads, but I use a very "pointy", long-bevel 1/4" spindle gouge for most of the smaller details and very small diameter shafts and spindles. These tools cut with less resistance, allowing you to make thinner, finer finials without as much chatter, flexure, etc... with practice you'll be holding the tool with one hand while using the other to steady the turning wood. Stubby tools with short, blunt bevels are safe for beginners, and far less "grabby", but you'll be hard pressed to turn anything fine and delicate with them.

4. AVOID THE TIP OF THE GOUGE. If you are working on a small diameter finial or spindle, say less than 1/8" and smaller, and you allow the tip of the gouge to cut, the wood can try to 'climb' up and over the gouge, and snap. If you keep the handle low, and keep the tip of a long-bevel gouge up high, not touching the wood, and cut on the side or wings of the tool with a very fine, shearing cut, you will be less likely to snap off fine spindles, and they won't try to climb up the tool. You may need to lower the rest to allow you to lower the handle and still have good bevel contact. With practice, this sort of cut can be a very accurately controlled, and the shiny-smooth cut will require very little sanding.

Maybe within a few weeks I'll be past the crazy-busy period in the solar industry, and I'll get to actually turn a few finials myself!

Safe spinning,

Brad Vietje

Newbury, VT

Re: tools for turning finials

#27

Thanks, Brad....

Allen Neighbors

>That is really informative. I turned a finial yesterday, and one today, and what you say has really made sense to me with some of those cuts still fresh in my mind. I also know what made one of them break, now, thanks to your little tutorial.

Thanks againk, Brad. It is appreciated.

Re: tools for turning finials

#28

gouge tip, solar energy

John K Jordan

>Brad,

>4. AVOID THE TIP OF THE GOUGE.

You stated this more clearly than I did earlier in this thread.

After learning the hard way I now do this by instinct and didn't even realize it until I was teaching several people how to turn tops recently. An 1/8" handle needs some of the same techniques as a finial. Cutting a cylinder or taper with the wings as you described is almost like planing with a very small skew, but with the advantage of handling a steep cove as well as allowing a seamless transition between the two shapes without lifting the tool, i.e., you can begin a cove cut with the tip then transition to the side of the gouge as you hit bottom.

Another thing which really helps is using the left hand as steady rest during these cuts.

BTW, we may have had this conversation before, but what do you do in the solar industry? Google shows me a solar store in Groton, VT with your name on it. Are you involved in technical development as well as sales/installation? Before I retired from ORNL I worked in part on developing a fiberoptic-based solar collection system - good clean fun and with patents and awards and a spinoff company (not mine!) to show for it.

JKJ