Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Newbie turner question - finish for rolling pin?

Posts

Newbie turner question - finish for rolling pin?

#1

Newbie turner question - finish for rolling pin?

Glenn Madsen near San Francisco

>I'm basically a flat wood worker, who occasionally picks up the lathe tools and makes something. Today, it was a simple french style rolling pin. I had some scrap anigre, and turned a 16" pin, about 2.5" in diameter.

It's sanded to 400, burnished with the shavings and looks pretty nice.

So: Oil? Shellac? Wax? Varnish? Leave it alone?

Still mounted on the lathe, but coming off later today. This is a gift, among others, for a newly married niece.

Re: Newbie turner question - finish for rolling pin?

#2

JL

Mineral oil for rolling pin

JL

>Or "butcher block" oil. That's what I typically use for mine. I typically raise the grain a couple of times first - it is going to get exposed to moisture.

Re: Newbie turner question - finish for rolling pin?

#3

The best finish is no finish

Ron in Drums PA

>

Re: Newbie turner question - finish for rolling pin?

#4

Steven Antonucci

Mineral Oil or nothing

steve antonucci

>I make spoons from time to time, and it's nice to oil them up for a presentation, but after that, they go into the kitchen...

If you are making it for use, I wouldn't concern myself too much about looks today. You can't wear off what isn't there...

Steven

Re: Newbie turner question - finish for rolling pin?

#5

Re: Newbie turner question - finish for rolling pi

Barbara Gill, Remlik VA

>I use Claphams Bees Wax/Mineral Oil salad Bowl Finish. That way it looks nice for the gift part but the finish is edible and will wear off with use.

Re: Newbie turner question - finish for rolling pin?

#6

Re: Mineral oil for rolling pin

Glenn Madsen near San Francisco

>This grain raising: Done with water, some other solvent, or oil? Then re-sand with super-fine?

I've got some of this anigre turned into a small carver's mallet, and it does look good with a non-film finish. Ambers up some, too.

Thanks!

Re: Newbie turner question - finish for rolling pin?

#7

Re: Newbie turner question - finish for rolling pi

Glenn Madsen near San Francisco

>This looks interesting. Finding a local source seems to be a challenge, though, and this needs to be delivered late this week.

Howard's Beeswax/Carnuba/Orange Oil seems a locally available alternative, though. Wonder if I can find an MSDS on it...

Re: Newbie turner question - finish for rolling pin?

#8

Re: Newbie turner question - finish for rolling pi

Jim Pugh, Elyria, OH

>Glen, go to the grocery store and get some mineral oil. Been used on wooden cutting boards/blocks for ever. Wipe it on, wipe it off and instruct the new bride to do the same when the wood starts looking dry. It has no detectable taste and is safe for internal use.

If you want to make something similar to what Barbara Gill mentioned the just mix 1 part beeswax to 4 parts mineral oil. Smells nice too.

Re: Newbie turner question - finish for rolling pin?

#9

make your own

Ron in Drums PA

>Go to the drug store and buy some beeswax and mineral oil.

Warm the oil enough to melt the wax, pour it into a jar, then label it "Glenn's Butcher Block Oil" :-)

If you want to get fancy, melt in some carnuba wax and call it "Glenn's Spiffy Butcher Block Oil" :-) :-)

PS. Woodcraft sells carnuba and beeswax

Re: Newbie turner question - finish for rolling pin?

#10

None at all

Galen V

>I agree with post on no finish but if not cared for salid bowl oil is fine to help restore. Best hope is being young she has learned baking from someone older. DO NOT PUT IN THE DISHWASHER! Hand wash quickly after use and hand dry. Scary thing is my grandmother baked for schools all her life, I am not sure the rolling pins she used every had time to see water and were generally flour coated. We never died from it!

Re: Newbie turner question - finish for rolling pin?

#11

Re: The best finish is no finish

Harry In beautiful downtown Kulpsville

>I agree with Ron. Sand it smooth and leave it alone.

Re: Newbie turner question - finish for rolling pin?

#12

Re: Mineral oil for rolling pin

Barry Irby

>Just wet it with water. Either pass it quickly under the faucet or use a wet paper towel or cloth. Liberally wet it and wipe it off immediately, then lay it aside to dry thoroughly, maybe over night. Sand again with whatever fine sand paper you used, 400 or what ever. I would use a fresh sharp piece of sandpaper and sand with the grain. What you will get is a lot of little fine whiskers and they should come off easily with sharp paper.

Re: Newbie turner question - finish for rolling pin?

#13

Re: Newbie turner question - finish for rolling pi

Russ Fairfield

>You should be asking this question of a cook, not a bunch of woodturners. The cook will tell you the best finish on a rolling pin is no finish at all.

The worst finish is anything that can come off and leave flakes in the pie crust.

Barb suggests a good compromise with something that makes it look good when it is new, soft enough to come off easily, is edible, and is totally compatible with the shortening in the pie crust. .

Re: Newbie turner question - finish for rolling pin?

#14

beeswax/mineral oil

advice from a baker

>glenn --

the rolling pin needs to be seasoned -- sealing the wood pores with something other than flour.

a good first seal is a light coat of shellac with successive applications of some sort of waxy coating. the beeswax/mineral oil (50/50) works great, but you can also use nut or other food oils depending upon how often the rolling pin is used -- these types of oils can go rancid.

Re: Newbie turner question - finish for rolling pin?

#15

Thanks, all!

Glenn Madsen near San Francisco

>I found a lot of help from you good people.

I also found a bottle of 'block oil' in my shelves, from some time in the '80's, purchased from Williams & Sonoma. Some sort of bean oil, according to the label, with citrus and vitamin E and the like. Doesn't go rancid, according to the label. I bought it for a cutting block that we've been using for those 25+ years, and it's done well.

So I wiped some on, and burnished it in. We'll see how it looks this morning, after it's dried. If it's all munged, I guess I can turn another pin...