Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

OT: Need a logo made

Posts

Re: OT: Need a logo made

#26

Maybe not a logo

Ed in Leaside

>Perhaps you're not looking for a logo per se. Normally, a logo is designed to be a mutli-functional element suitable for use on business cards, brochures, letterheads, invoices, signage, etc. If you're just looking for a graphic element to highlight a web page header, that's different. It may or may not be a derivative of a logo. Here's a simple example: a spiral against a curved surface, the type (VAG rounded) is a tool handle, and the negative space under the spiral is a tool bit. The graphic, sans spiral, could be mirrored to the right, and both could be stretched to span the page. You could swap out or drop "tools" for other pages of your site.


img

Re: OT: Need a logo made

#27

Nice Concept and Theme

jerhall

>

Re: OT: Need a logo made

#28

Re: Maybe not a logo

John Jordan

>That's exactly what I want Ed, a logo just as you described, not just a page element. I want it to say JOHN JORDAN WOODTURNING with, or without an additional simple graphic element. Strong, simple, bold *may* be good words to describe it. Sorry, if I was better at this, I might have been able to do it myself-I guess I should have tried. :-)

John

Re: OT: Need a logo made

#29

Re: Maybe not a logo

Bob Macgregor

>Ed,

Maybe if you put a solid bar framing the "woodturning tools" with a sharp tip cutting the curl from the surface?

Re: OT: Need a logo made

#30

Re: Maybe not a logo

Ed in Leaside

>I'd thought about reversing the type in a bar, but reverse type is harder to read. Also increased busy-ness reduces the strength I think Jon is looking for.

Re: OT: Need a logo made

#31

Re: Maybe not a logo

Ed in Leaside

>So yes, you need a logo and a page element. :-)

I'd left out the John Jordan part in the above example because I'm lazy, or more because there'd be no point in sifting though my 3000 font arsenal looking for a suitable match for VAG rounded if the concept wasn't going to go anywhere. I'd left that to your imagination. There is a blue keyline around the example BTW, a forum placement holder, which shouldn't be there.

Keywords for a tool logo, my opinion, should be Strong, Hard, & Sharp. I'm curious as to what you've been sent off the board. Anything you can use? As this is slipping down the page and interest may be waning, I wondering should we continue? On or off ...

Gotta run, street recycling bin signage today, for an HVAC client. :-)

Re: OT: Need a logo made

#32

Re: Maybe not a logo

John Jordan

>Ed, Thanks, I see where you were going with that and Isee all the possbilties it has. Leaving things to my imagination is part of the problem...seeing it helps. You've been helpful, as have a number of folks here. I have gotten several off the board, and some good ideas. It's still cooking and I'm still open.

John

Re: OT: Need a logo made

#33

Re: Maybe not a logo

Bob Macgregor

>Ed,

I wasn't thinking of a solid bar with reverse-tone words. I was thinking of a horizontal black bar above the wording with the left end terminating just under the curl. A short, diagonal bar would go from the curl down and to the right to meet the left end of another horizontal black bar underlining the wording. Unfortunately, to make it more visibly distinct, you couldn't have the bevel rubbing!

BOB

Re: OT: Need a logo made

#34

Re: Maybe not a logo

Ed in Leaside

>Showing the bevel rubbing, in this day & age, with the proliferation of color, would not be a problem. To have the upper bar meet the bottom of the spiral would require moving the spiral up, and to keep the spiral focused on the centre line it would have to be reduced in size. Somehow I can't see it working. :-)