Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Looking for cheaper replacement chuck key *LINK*

Posts

Looking for cheaper replacement chuck key *LINK*

#1

Looking for cheaper replacement chuck key *LINK*

ILYA ZAVORIN

>I have a Oneway Stronghold chuck which is about 1 year old. Last week I managed to lose its key. Oneway will be happy to replace it, but it'll cost about $60 including S&H. Does anyone know if I can get a matching key from a "generic" manufacturer (probably Chinese) for less than that? Thanks much.


http://www.oneway.ca/chucks/stronghold.htm

Re: Looking for cheaper replacement chuck key *LINK*

#2

Re: Looking for cheaper replacement chuck key

john lucas

>That's why I went with the Vicmarc chuck. It uses a standard Hex wrench. That paid off recently. I went to a demo and left my chuck key. Fortunately it was easy to pick up a 10mm T wrench and that got me by.

Re: Looking for cheaper replacement chuck key *LINK*

#3

Wrong Perspective on problem

Bill Howatt

>You did not lose the chuck key, you created an opportunity to buy another chuck.

If you buy the Stronghold body only kit, it comes with a key (mine did). Yes, the cost is higher but you now have another body that you can get a different set of jaws for and enhance your turning experience.

It is unfortunate the keys are so expensive and I have never heard of an alternate source for them but maybe somebody else has.

Bill

Re: Looking for cheaper replacement chuck key *LINK*

#4

cheaper replacement chuck key..question

Stuart Johnson

>This comes up from time to time. What is the difference between the chuck keys like on OneWay and Nova chucks and drill chuck keys?

Re: Looking for cheaper replacement chuck key *LINK*

#5

Re: cheaper replacement chuck key..question

Allen Neighbors

>Stuart, Oneway's keys are like an enlarged chuck key for your drill. Nova's chuck keys are six-sided like an allen wrench.

Re: Looking for cheaper replacement chuck key *LINK*

#6

Re: Wrong Perspective on problem

Ilya Zavorin

>Yes, but there is also a possibility that I will lose that key as well, in which case I'll have two unusable chucks. ;-)

Re: Looking for cheaper replacement chuck key *LINK*

#7

Steven Antonucci

That's brilliant!

steve antonucci

>It's like getting the body with a $60 off coupon...

And you can never have too many chuck (unless you have more bodies than jaws... that's too many!)

Steven

Re: Looking for cheaper replacement chuck key *LINK*

#8

Steven Antonucci

Not the older SuperNova's

steve antonucci

>I have a Super Nova with geared teeth. The Super Nova II had the hex head, and is a WAY BETTER chuck. The original teeth and gearing have all worn over, and the chuck no longer holds things firmly.

I have dedicated it to my cole jaws...

Steven

Re: Looking for cheaper replacement chuck key *LINK*

#9

Re: Wrong Perspective on problem

Bill Howatt

>Now that you've lost one, you will be more careful. Did you leave it behind somewhere, lose it in the shop or just drop it in the shavings? I sympathize with you, I have lost bigger things than the chuck key that should have been easy to find in all my junk!

There have been posts about the replacement cost of the Oneway keys before but I've always thought that they were too big to casually lose by dropping in the shavings. I must admit it is amazing how a pile of shavings can swallow things.

Another potential problem is that after you buy the replacement key the lost one will turn up.

Re: Looking for cheaper replacement chuck key *LINK*

#10

Make a special place for your chuck key.

david

>And hopefully chances are less for it getting lost. I got two rare earth magnet discs with a built-in hook. Placed them side-by side on the front of my headstock, and now I have a rest for the t-bar of my geared chuck key to hang from. Very convenient to the headstock spindle. The hex-type key for my newest chuck goes into a 1x wooden shelf rest drilled with lots of holes to insert various accessories: live centers, #2 MT drives, drill chucks, drive spurs, etc.

Re: Looking for cheaper replacement chuck key *LINK*

#11

Steven Antonucci

I have a cheap metal detector for the pile

steve antonucci

>It was a Christmas gift for my son, and I occasionally call on it to find things in the pile. Works pretty darn nice. For small things like cutting bits, which I lose all of the time, I locate it in the pile, then pull out a section and wand it.

If it beeps, I cut it into two piles and wand both. The one that beeps gets cut again. And so it goes. Usually can find a needle in a haystack in less than a minute.

Steven

Re: Looking for cheaper replacement chuck key *LINK*

#12

Re: Looking for cheaper replacement chuck key

Fog Tanner

>My preference is to loose unimportant things like eye glasses and sleep. Loosing a chuck key is simply uncivilzed.

You might try one of the machine shop supply places like Wholesale Tool or MSC. If you have one locally you could take your chuck in and see if they have anything.

Like John, I cured the problem by going to Vic, which uses a key that you can pick up at Wholesale, MSC, Home Despot, etc. I did this after going the route of a chuck body only Stronghold. Now I have a key for each machine.

I worked in a machine shop out of high school and going to college. I ran an engine lathe which had a "tray" built into the top of the headstock. You learned to pick up the key and replace it with your left hand. It became an automatic operation and I never left a key in the chuck and started the machine. I have seen that happen and a 2hp lathe can throw the key across the room - one reason you see lathes angled when one is behind another. Once you get in the habit, it is difficult to loose your chuck key, or start the lathe with it in the chuck. You will know when something doesn't seem right before you tirn the switch or go walking around with the chuck key in your hand to the bandsaw.

I have a dust collector hood sililar to the pictures in Raffan's books. I used some PVC pipe and fittings to make a rack which is mounted to the hood. A Oneway chuck key will fit in a pice of 1" PVC. I actually have a 1" T mounted on its side which has a short horizantal piece with holes drilled it it for my Vic T handle keys and tommy bars. This T is connted to another T, which has a short piece for my allen wrenches used on the chucks.

For the jaw screws I loose in the shavings, I now have a large magnet. Has aved a couple of hours digging through a pile of shavings at 2 in morning when I just had to finish something.

Re: Looking for cheaper replacement chuck key *LINK*

#13

Re: Looking for cheaper replacement chuck key

E.T.

>Fog: This PVC rack sounds good. Is there any way you could post a photo? ET

Re: Looking for cheaper replacement chuck key *LINK*

#14

Jesper, Denmark

Re: Not all keys are the same.....

Jesper, Denmark

>Some years ago (10+?) Oneway changed their Stronghold Key/drive gear design. They are not much different, but just enough that the keys are different. I happened to get one type with the lathe and bought another chuck a little later, and they are different.

It is almost impossible to see which is which, but the two keys only fit in therir "own" chuck.

Not relevant to more recent purchases, but just be aware iof you have an older Stronghold and want an extra one.

Re: Looking for cheaper replacement chuck key *LINK*

#16

Re: Looking for cheaper replacement chuck key

Fog Tanner

>I'll charge the batteries in the camera and get one later today.

Re: Looking for cheaper replacement chuck key *LINK*

#17

12 spline vs 11 spline

Rick Allen

>The old Stronghold chucks have a 54 tooth scroll that uses an 11 spline key. The newer Stronghold chucks have a 59 tooth scroll that uses a 12 spline key.

You can "upgrade" the scroll on an old stronghold chuck to the newer 59 tooth variety for a price. You can not buy an 11 spline key from Oneway (or from anywhere I know of) so if you lose the 11 spline key the fix is to replace the 54 tooth scroll with the newer 59 tooth scroll.

The spline portion of one of my keys isn't fully seated and I find that key works okay with either the 54 or 59 tooth scrolls. However the greatest power can be achieved with the key which was designed to work with the chuck.

Re: Looking for cheaper replacement chuck key *LINK*

#18

Re: 12 spline vs 11 spline

Denis Lalonde

>Chuck key with 11 spline are available from Oneway. call them and ask for the old style chuck key...I ordered one today from Woodchuckers...

Denis