Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Help!! Hunter Tool stuck!!

Posts

Re: Help!! Hunter Tool stuck!!

#26

Steven Antonucci

He said it was 1/16"?

steve antonucci

>I didn't think they came that small? I assume he's exagerating?

P.S. My Chevelle went to the scrap yard before those things came out. I still don't own a set, but I will the next time I break a bolt I can't get visegrips on :-)

Steven

Re: Help!! Hunter Tool stuck!!

#27

You're Allen

Mark Mandell - Gone Round In Jersey

>Not to be confused with Steve [Schmock! Schmock!], Woody [What's Up Tiger Lilly?], Ethan [Green Mountain - not a musical group - Boys] and several other Allens, or the guy who actually invented the thing in 1926 and whose name is rather far from any form of Allen, Egidio Brugola AMT.

Actually we (North Americans) call it an "allen" wrench (or "key") because of the trademark of the Allen Company in Hartford Connecticut. But alas, no reported fetishes (well hexagonal ones anyway).

|;-}}}

Re: Help!! Hunter Tool stuck!!

#28

Thanks, Keith, that's my

Allen Neighbors

>next maneuver, as soon as I get back out to the shop after lunch.

I located a #7 torx driver, and it's not doing the trick.

Thanks for the good idea.

Re: Help!! Hunter Tool stuck!!

#29

Boy, am I dense!!!!! :))

Allen Neighbors

>

Re: Help!! Hunter Tool stuck!!

#30

Right... just about 1/16 diameter head.

Allen Neighbors

>

Re: Help!! Hunter Tool stuck!!

#31

That's what I have. :)

Allen Neighbors

>

Re: Help!! Hunter Tool stuck!!

#32

LOL! :)

Allen Neighbors

>

Re: Help!! Hunter Tool stuck!!

#33

Steven Antonucci

If the head is shot, just drill it out

steve antonucci

>and the cutter will fall off. You should then be able to get visegrips on the remaining stud. You don't need to worry about damaging the cutter if it's carbide- the drill bit will fail first.

Steve

Re: Help!! Hunter Tool stuck!!

#34

Re: Lathe Lighting....

Tim Grenville-Cleave

>Soak in diesel fuel for 24 hours ... then on reassembly use 'Copperslip' antisieze compound.

Re: Help!! Hunter Tool stuck!!

#35

Re: If the head is shot, just drill it out

Allen Neighbors

>If I could drill it out, shaky as I am, I would... but I have a drill press. And it shakes almost as bad as I do. :))

I'm going to try the leather and pliers, as was suggested. We'll see how it goes....

Re: Help!! Hunter Tool stuck!!

#36

Well, the leather and pliers didn't work.

Allen Neighbors

>Still applying the PB Blaster....

Re: Help!! Hunter Tool stuck!!

#37

Steven Antonucci

Hand held drill

steve antonucci

>There's probably less than 1/8" of metal to be drilled and the Torx screw will center the bit more or less. The carbide won't even scratch if the bit wanders. I tried cutting carbide with all kinds of things before I gave up. I made a scraper burnisher out of the carbide rod and lived happily ever after.

Probably take you 10 seconds, including chucking up the bit.

Steven

Re: Help!! Hunter Tool stuck!!

#38

I told you I was a klutz!!

Allen Neighbors

>I tried the leather and pliers again this morning. The cutter was cutting into the leather. So I used a little thicker piece of leather, squeezed the pliers too hard, and the little cutter crumbled. :(( With the cutter broken away, the screw came out easily with the pliers.

Now I have to order another cutter, and also locate some Neversieze!

I love this Hunter Tool. I know the whole problem has been my own fault, and not the tool's... I'm so disgusted with myself .........

sadly signed,

by His Klutziness,

Allen Neighbors