Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

waste blocks

Posts

waste blocks

#1

waste blocks

Carol - now in NC Nebraska

>Wally taught me to use waste blocks to get the most of out my turning blanks. I got all this lovely wood for Christmas and I want to get the most out of it!

Problem is I can't get any alder or soft maple or poplar around here to make some waste blocks.

Would someone be interested in sending me some 6/4 alder or soft maple or poplar to fit a Priority Mail box? I want to make waste blocks in the neighborhood of 3-5" in diameter.

PM me if you are game.

Alternative is I am going to Kearney, NE on Monday. Anybody know a place there I could get some?

Thanks.

Re: waste blocks

#2

Re: waste blocks

Mike Jones, Redding, CA

>Carol, You can make waste blocks out of anything...anything that is sound anyway. Plywood, MDF, two by fours...

Re: waste blocks

#3

Re: waste blocks

Bill Hale / The Wood Spinner

>Carol

See if you can find any old hardwood pallets.

Bill

Re: waste blocks

#4

JL

Re: Pine, spruce, "whitewood", fir...

JL

>all can be used. Just go by the building supply store and look for a relatively close-grained piece. If you want to try a construction site, that works too - just don't use pressure treated.

Re: waste blocks

#5

Re: Pine, spruce, "whitewood", fir...

bernie feinerman

>Avoid using plywood for waste blocks since the plywood can delaminate if you get a catch.

Re: waste blocks

#6

Re: Pine, spruce, "whitewood", fir...

Carol - now in NC Nebraska

>I got a 2x6 and it split along the grain. Lost a nice little walnut bowl in the process.

Nope, no soft wood!

Re: waste blocks

#7

Re: waste blocks

Wally Dickerman in Arizona

>Carol, I can send you some alder. Do NOT use MDF or plywood. Either can separate, especially the MDF. You don't want any flying objects bouncing around your shop.

Wally

Re: waste blocks

#8

Re: waste blocks

Carol - now in NC Nebraska

>I know better, Wally. I PM'ed you back. Thanks.

Re: waste blocks

#9

Beg to differ..

Mike Jones, Redding, CA

>I pick up cabinet grade birch plywood and MDF cut offs free from a local cabinet shop. Using plywood for waste blocks has distinct advantages. Plywood is dry (an important feature for your mounting method) it is uniform and without defects that can cause screw failure, and has a true and flat face without any planing and assures one of good contact with the glue surfaces. I do not beleive that sound plywood will delaminate when used this way.

MDF is nice to work with too, but will not hold screws as well as plywood. I'd be interested to know if anyone here has had plywood or MDF problems when used for waste blocks. Maybe I've just been lucky so far.

Re: waste blocks

#10

Carol, how would you like a ...

Allen Neighbors

>flat rate box with a large chunk of Aspen? It is very soft wood.

Spell the 'very' with large, black letters. :)

Got anything you want to trade?

Re: waste blocks

#11

Disregard the above; How about

Allen Neighbors

>some Sweetgum? It's perfect for wasteblocks, bowls, ringkeepers, etc.

:)

Re: waste blocks

#12

Re: Disregard the above; How about

Carol - now in NC Nebraska

>I'll PM you.

Re: waste blocks

#13

10-04, PM.

Allen Neighbors

>

Re: waste blocks

#14

Re: waste blocks

Jim Miles- Charlotte NC

>Carol:

I use waste blocks on 95% of what I turn.

I use almost exclusively 2 x 6s, 2 x 8s scraps from building construction, you have to be a little selective and avoid anything with knots of splits, cracks. However most construction site throw lots of it in dumpster daily. I concure with plywood - it will split apart. I run 2xs through planer to flatten the side that will be glued. Also have used TREX - composite decking material avial at Lowe's, made of recycled sawdust & plastic bags. Does not glue quite a well as wood, but does have some positive properties - no grain, knots, cracks etc.

Re: waste blocks

#15

Re: waste blocks

GaryG in MD

>Carol,

I have always used Borg generic 2x4s and never had a single problem.

I handle them like any other wood -- lop off a 4x4 square and put it between centers; turn a chuck tenon and round it up from inside to outside with a bowl gouge; reverse and face it slightly concave to hold some glue, and you're all set.

Yes, the chuck jaws will compress it a bit -- just put a mark on it so it always goes in the chuck with the same alignment. I get a board and make a bunch of them all at one time -- it goes pretty quickly, and then you have a stash for future use.

I use medium CA to attach it to the work piece -- never had a failure. (knock wood!) If you had a truly horrendous catch, you'd probably be well served if the block did tear off and limit the force on your tool and hand/arm.

...Gary

Re: waste blocks

#16

You just a lucky man!

Steve Mushinski

>Yes Mike you have just been lucky so far.

I have not tried MDF and wouldn't as it is just sawdust. I have tried plywood and yes it did separate and break off.

One catch and you might be catching your turning off your face shield.

Steve

Re: waste blocks

#17

Plywood

tek-Brunswick, Ohio

>Speaking from over 30 yrs experience as a carpenter. There are many types of plywood, some ate suitable and some are not. I would stay away from most of the construction grade plywoods. Cabinet grade birch is pretty decent stuff. Underlayment grade plywoods are also pretty good. Baltic birch is great, but there goes the low cost. I too would stay away from MDF it splits rather easily and is very dusty to cut. Run some MDF though your table saw and you will find out how good your dust collection is and using a router on it can make any day a cloudy day. The 2 X 6 should not have split on you unless it already had a crack in it or you did not drill proper pilot holes for your screws and cracked it with the screws.

Re: waste blocks

#18

Re: Plywood

Wally Dickerman in Arizona

>Yep, you seem to have been lucky so far. Solid wood is just safer than plywood. Carol uses a screw chuck and if she used MDF, after one or two healthy cuts the threads would be stripping out. The blank would be wobbling and may even be airborne.

Have I seen these things? Sure have. In my town we a have community woodshop that has 7 lathes. In 10 years time I've seen just everything happen that could.

Wally

Re: waste blocks

#19

Re: Plywood

JohnKJordan in East TN

>>...Solid wood is just safer than plywood.

Would that not depend on how well the plywood is glued (i.e., is not glue as strong or stronger than wood if done right?) I thought quality plywood could actually be stronger than solid wood - it certainly cannot split along the grain, at least not through the thickness. You can't easily split it with improper pilot holes as you can with a solid piece of wood. Comparing the two would also have to take into consideration any defects, perhaps hidden, in the solid wood.

I'd would, however, be afraid of MDF.

JKJ

Re: waste blocks

#20

Plywood and MDF

Ron in Drums PA

>Most people who fear plywood have only used the cheap, construction grade stuff.

High grade plywood, the type used in furniture, works. There are no voids to worry about. The glue joints are as strong if not better than what most can get when one glues on waste block.

I use plywood scraps from furniture projects, so cost is not a factor.

If furniture grade plywood doesn't work, than it goes to reason that you shouldn't glue on waste blocks either.

MDF makes great jam chucks for small boxes. I turn a 3"+ disk then I mount into a chuck using 3" jaws.

I also made a vacuum chuck from MDF and no problems.

Re: waste blocks

#21

Re: Plywood

Wally Dickerman in Arizona

>Well sure John, I'm sure that there must be plywoods available that have plenty of strength to be used as glue blocks. Until I part the bowl off. I part down the glue line until the joint is about the size of a dime on small bowls, before I pop it off with the heel of my hand. I wouldn't trust plywood to hold that. My personal preference is still solid wood. Alder is my choice for a couple of reasons. Alder doesn't warp, so I always have a flat true surface for a glue joint. Alder is soft enough that it parts off easily, but it doesn't tend to split and break when parting off as some woods do. I have a source for kiln dried, unplaned (a full 1 in. thick) 4/4 alder that is just about perfect for glue blocks. It's not expensive. A 1 x 6 piece of alder 4 ft. long is about $5...enough for perhaps 30 glue blocks.

Wally

Re: waste blocks

#22

Careful, Carol...

david

>or you might end up with a repeat of the great Valentine's Day Overload ;-).

Re: waste blocks

#23

Re: Careful, Carol...

Carol - now in NC Nebraska

>Well David, I am always up for more wood. :) Waste not, want not. Doesn't work with waste blocks however. L0L! There it is no waste, want block.

As for Valentine's Day, that was for the other Carole (note the 'e'). I'm the Christmas Carol (no 'e' but a half dozen boxes of wood for Christmas from generous turners).

Heh! Maybe there is 'Carol" out there for each holiday!

Re: waste blocks

#24

Re: waste blocks

eliot d

>I just though I'd pass on that Cindy Drozda told us at a demo that she's quite particular about which wood to use for waste blocks. I can't remember all the ones she recommended -- except mahogany was one of them. I suppose you could ask her.