Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Help, technical machinery question

Posts

Help, technical machinery question

#1

Help, technical machinery question

Ruth Niles

>I think you all remembeer my stuck face plate saga. Then the front bearing needed replacing because I believe I melted the lubricant in it. During the process of disassembling the headstock, using a block of wood with a hammer to move the pulley back enough to expose the key lock, the wood slipped upwards and broke a small piece of the smallest pulley section. About 3/4" - 1" in a half-moon shape.

I cleaned it and glued it back, filed it smooth so you can't even feel it and the belt rides true.

I replaced the front bearing, there was a vibration when I turned a test piece. General said the pulley is off balance because of that tiny break, a machinist who makes lathes said I probably messed up the rear bearing because of all the pounding necessary to remove and replace everything in the headstock. So I replaced the rear bearing. He said whenever you remove a bearing, which I had to do to get to the front one, it has to be replaced.

With nothing on the lathe it runs quiet and absolutely true and smooth. With wood on, I'm not happy, I can't get a clean cut, it's like the wood is vibrating. I put the belt on the second step in the pulley but that cuts the speed in 1/2, it's more torque but not enough speed.

Before this lathe goes out the door and I take up glass blowing, any thoughts or suggestions?

Re: Help, technical machinery question

#2

Re: Help, technical machinery question

Charles B. Watson

>Have you checked to see if there's any side to side play in the spindle, i.e. run out?

Re: Help, technical machinery question

#3

Knitting has fewer technical difficulties :-)

Clem Wixted, Jonesboro, AR

>

Re: Help, technical machinery question

#4

Re: Help, technical machinery question

JohnKJordan in East TN

>When you filed it smooth, I assume you did so with the lathe turned off. This may have created a small irregularity that might not interact until the belt was under tension, i.e., when you applied torque by putting a tool to the wood. You'd have to be careful, but if you can access it while running with the belt on a different step, you might detect the irregularity with a piece of wood rubbing against the inside of the smallest step. If so, perhaps it could be "machined" while spinning with a file and/or sandpaper glued to a stick. (be real careful!)

But can you not just replace the pulley? If you can't get one from General, you can buy a stepped pully set from another source.

BTW, a future daughter-in-law is a glass blower, and from what I hear, you don't EVEN want to consider that as a casual hobby unless you have access to a glass studio next door!

JKJ

Re: Help, technical machinery question

#5

Re: Help, technical machinery question

Ruth Niles

>John, I could replace the pulley, it's $160 (plus shipping?) from Canada. The place where I got my bearings sells pulleys but they don't have the indexing on the end.

The piece fit in almost perfect, I used a small file to smooth it with the lathe off then with it running at about 3 (?) rpm. When the lathe is running, you cannot see any "jump" or bounce on that small pulley section. The lathe reacts the same no matter which step the belt is in. I'm dreading the thought that I messed up the front bearing AGAIN doing all this work on it. I'm told those bearings are very percision balanced and can be damaged with the slightest pounding.

I was kidding about glass blowing, I'll take up retiring all together!

Re: Help, technical machinery question

#6

Re: Help, technical machinery question

Ruth Niles

>Charles, there's no movement of any kind. My neighbor has one of those things you put on machines to measure that stuff. Like how I know all those technical terms?!?

Re: Help, technical machinery question

#7

Check a couple things

tek-Brunswick, Ohio

>Did you snug up all of the set screws on the pulley? Did you make sure the key was back in the keyway properly. Did the putty slide more toward the tailstock or the headstock than it was before? The belt needs to run at 90% to the pulleys. If one or both of your pulleys have shifted the belt runs at a slight angle to the pulleys and can cause virbation.

Re: Help, technical machinery question

#8

Re: Help, technical machinery question

Doug Thompson near Cleveland

>Ruth, make sure everything is tight including the nut by the hand wheel that hold the assembly together.

Re: Help, technical machinery question

#9

Re: Help, technical machinery question

wilbur

>You mentioned that you used a block of wood and a hammer to remove the bearing the first time. Did you use that method when you replaced the second bearing?

The best way to remove and install bearings is to use a bearing press. You can improvise one using clamps and appropriately shaped pieces of wood (think piece of wood with a hole in it fitting around the shaft). But they only cost about $50, and they make the job much easier.

Re: Help, technical machinery question

#10

Reorder, remove, and reinstall

Eddie Pacheco; San Jose, Ca.

>Ruth,

Without getting a feel about how severe the vibrations is via a note, I think you will have to repeat the whole process.

Because these bearings are precision pieces, they have to be installed very carefully. Banging, now matter how lightly, causes facets on the bearing race. This time you nead to really disassemble the spindle assembly.

If the bearings are a tight fit onto the housing you need to chill the bearings and warm the housing to allow the parts to slip together with only hand force. Refrigerator for the bearings and a heat gun for the housing,not a torch.

If the bearings are do not slip fit onto the shaft the shaft will have to also be chilled before sliding it through both bearings.

This is because we don't have the proper alignment jigs at home like they do at the factory for putting these things back together again.

If there is a preload nut for the shaft check to see if you have it tight enough.

Re: Help, technical machinery question

#11

Re: Help, technical machinery question

Robin Corell in Atascadero Ca

>If I understand you correctly the lathe runs true and vibration free with nothing mounted, and the vibrations only appear when wood is mounted. This makes me think that the vibration is coming from how the wood is mounted. Faceplate? Chuck? If you ae useing a tailstock I would check its allignment as well as the bearing of the live center. maybe try turning a spindle with a drive spur just to see if it is your faceplate/chuck.

I had a similar problem on my delta and it turned out to be the outboard hand wheel was slightly bent.

Robin

Re: Help, technical machinery question

#12

Re: Help, technical machinery question

Wally Dickerman in Arizona

>If the lathe runs smoothly without a piece of wood, I would suspect a tailstock problem, assuming that you are using one.

Wally

Re: Help, technical machinery question

#13

Re: Check a couple things

Ruth Niles

>Check to everything you asked. The pulley is right where it was, the set screw is in the identical same place. The belt is running straight up and down.

Thanks for the additional check list. Sort of wish one of them was the problem so I could start looking for the answer.

Re: Help, technical machinery question

#14

Re: Help, technical machinery question

Ruth Niles

>Wilbur, I followed the directions that Christian from General (in Canada) gave me. It's a bit difficult to use clamps for disassembling the headstock. I did take the new front bearing and the spindle to a machine shop and they pressed it on in 30 seconds. The rear bearing has to be pounded in, and I did make a block of wood and hollowed out the center to fit over the spindle. That worked great.

Re: Help, technical machinery question

#15

Keith Tompkins

Re: Help, technical machinery question

Keith Tompkins

>Ruth, First, your pulley is precision balanced...notice the holes drilled in the largest diameter of your pulley under the belt for balancing purposes...I don't know if the whole pully/spindle assembly was dynamically balanced as a unit, but I wouldn't be surprised if it was.

Second, bearings must be installed with a set procedure. For example, hammering in the outboard bearing will put extreme pressure on the inboard bearing, in effect, you are attempting to blow the insides out of it. The inner race of the inboard bearing must be supported while the outboard bearing is driven in by both the outer and inner race. An old bearing works well to drive in the outboard bearing. Merely hammering in bearings will probably damage them, as the bearing surfaces absorb the impact. Let me know if you need more details, I can email you.