>Wilbur That is a tough shape to turn for a second bowl. A wider bowl with a more shallow, more gentle curve is easier to learn on. On a deep bowl like that it is harder to keep the bevel against the wood guiding the cutting edge. Pat yourself on the back for finishing it, but it would benefit you to learn tool control on easier shapes first. Sharp tools, bevel on the wood and controlled cuts are what you need at this point. Hogging wood out quickly looks impressive, but that should come after you learn tool control. Have fun you are doing great,
>This my opinion of the words and how we use them.
The definitions of "jam" and "jamb" that apply here are - "jam" as being to stick or force; and a "jamb" as being a protrusion or mass.
I would take that to mean that the correct spelling of the word would depend on how we are using it. We can refer to the "jamb", which would be the chuck itself because it is both a protrusion and a mass. Or, we can be referring to the act where we "jam", force and stick, the bowl on the "jamb". Is the proper use "jamming the bowl on the jamb"?
The word "chuck" is a little more difficult. We used to refer to "throwing" the work in the lathe to describe putting it in the lathe and spinning it. The capacity of a lathe was defined as being its "throw".
The word "swing" is a relatively new term to define lathe capacity, and nobody "throws" their work in their lathe anymiore.
There is also a common definition of "chuck" as meaning "to throw" something, as in chucking a rock. It isn't much of a stretch to see where "throwing" and "chucking" were used to describe the same thing, and the "chuck" became a means for gripping a piece of wood so we could "throw" it in our lathe.
I think holding the work by some other means is optional. Depending on the geometry, I've held some pieces securely by jamming alone.
Also, I sometimes use the tailstock to support blanks even when they are held with a "real" chuck, especially during initial cuts. This insures I don't lever the piece out of the chuck if I make a judgement error.
>I read over the previous responses. Almost all of them address the chucking methods. There is a limit to how much a chuck or even a faceplate will hold. If your technique is causing large catches something has to give. Launching the bowl is not the worst thing that can happen. If the bowl does not come loose something else will give. It could be the gouge will break or bend, or the tool rest. or you loose your grip on the tool and you have sharp metal flying through the air. Like Brian I use either the compression or the expansion method. I think Julie's video link may be the most useful answer for your problem. Learn the technique and you will not create enough stress to tear the wood from the chuck. You are on your way there, keep at it. You have completed two bowls and the second one is not an easy shape to hollow. Join a woodturning club if one is in your area. Most clubs have members that will help a new turner on his way. Here is a link to the list of AAW chapters to see if one is near you.
>My pet peeve is when I see the word tendon refered to as a woodworking term. It should be tenon. A tendon something that connects muscles to bone. Of course here in the south we always speak "good" english. Thanks Ya'll
>"That is a tough shape to turn for a second bowl. A wider bowl with a more shallow, more gentle curve is easier to learn on."
NOW you tell me. :@)
Thinking back, even taking into account the catches, I think my previous efforts at bowl blank orbiting were 10% catch, 90% not doing the dovetail recess right in the first place. I really left a pretty thin wall on the recess. I won't do that again.
>You are learning fast. One thing to keep in mind. Once you damage a tenon or a recess it is going to hold even less well when you remount the wood in the chuck. Reshaping the recess or tenon will help regain some or all of the original holding power. That depends on how badly the wood in contact with and near the chuck was damaged. Most bowls are turned cross grain to the tenon. It is not all that unusual to have o tenon split off of the bowl. Especially if the type of wood being turned is spalted or one that splits easily. Here again the first big catch causes havoc further down the road. So we strive to learn to not get big catches. All of us went through the same experience you are now. Remember,"Experience is something you get right after you need it!" Have you blown up a bowl yet? That can be an even more exiting experience.