Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

VS mini lathe - shopmade version

Posts

VS mini lathe - shopmade version

#1

VS mini lathe - shopmade version

Carol - now in NC Nebraska

>Hey All,

Some time back I got in on the Vega motor deal to make the mini lathe variable speed. Turns out my control boards didn't work. But this past week I met a lady who repairs TV's and trouble shoots to component level. Very few of those left in this world! She found lots of broken connections of the board due to muscling on the spade connectors. All fixed now.

So.

I drew up the wiring diagram with a cooling fan and a reversing switch. I had gathered all the Internet forum comments I could find on this conversion so I think I am OK.

However, there is an itch I'd like to scratch. Due to some conversation here recently concerning tachometers for the lathe, I got curious. Seems the bigger, fancier lathes have them. And there are TA1 and TA2 connections on the motor control board. I am told those are for RPM feedback. Wonder if I could hook up a digital tach in parallel to them and get an accurate reading?

Any electronic types out there that could give me some insight here?

As for a source for the tachs, I found electronics kits, under $30 on the 'net. I have a soldering iron and know how to use it. :)

Re: VS mini lathe - shopmade version

#2

Re: VS mini lathe - shopmade version

david

>Unless you are intending to do a lot of thread chasing (Allan Batty recommends 300 rpm), I don't see a big advantage to having a RPM read-out on your lathe. The speed of your lathe should be more based on feel than the number on any readout. Just my 2 cents worth (probably worth less than that in Canada these days).

Re: VS mini lathe - shopmade version

#3

Re: VS mini lathe - shopmade version

Bill Howatt

>I have a large lathe with no tach and I don't see any need for one. However, I will admit to having looked at the metal plate on my General to see what the range of RPMs are for the pulley and electronic speed knob setting are. I did it mostly for interest but it was useful so I didn't exceed the speed for my large Forester bits.

Before you jump into buying an electronic tach for your controller check the manual carefully. It may put out an analog signal from say, 0-10V that represents the RPM. In this case, a cheap voltmeter would do and they are certainly cheap these days.

Also, if you have a step pulley system to keep the torque up and the motor cooler at slow speeds, the gear ratio will have to be factored into any tach reading from the controller - it just knows what frequency it is putting out to the motor, not what is connected to the motor.

Bill

Re: VS mini lathe - shopmade version

#4

Carol, on the 18th, there is a thread *LINK*

Clem Wixted

>on stroboscopes. Bill Boheme designed a real simple and almost no cost strobe.

Here is a link to the thread:

http://www.woodcentral.com/cgi-bin/turning.pl?read=171990&v1=e2vrt43&v2=wood+turning&v4=sander&v5=nx3we6g

Clem

Or click this


No Cost Stroboscope Thread

Re: VS mini lathe - shopmade version

#5

Re: VS mini lathe - shopmade version

Carol - now in NC Nebraska

>I know there is that school of thought that RPM readout is not necessary. This is just an itch I'd like to scratch. Its too cold in the garage so I am sitting at the computer vicariously 'working.' :) Also my knees and hips are mightily protesting the cold temps. That also impairs my presence in front of the lathe making shavings and dust.

I am curious if the motor control board TA1 and TA2 can be utilized to provide sensor control to a digital tach. That a shorter path than including a sensing circuit with pick up, if it is possible.

Right now I am looking at variable speed lathes with the RPM readout, and their parts lists tp see what's what. Specifically the Grizzly G0632, which helpfully includes the parts list. Now if I can just find the price list for the parts list. :)

Re: VS mini lathe - shopmade version

#6

Re: VS mini lathe - shopmade version

Mike Cunningham (Cape May NJ)

>If you telephone or email Grizzly they'll give you a price for any part, including those that you can't find.........which is most of them.

Mike

Re: VS mini lathe - shopmade version

#7

Re: VS mini lathe - shopmade version

Ed Heuslein

>Howdy Carol: The TA1/TA2 lugs are for a feedback circuit and will not work for your tach. I also have a couple of the Vegas and have experienced several poor circuit board solder joints on both of them. ANY problems in the future should first be recognized as a probable bad solder joint - the voice of experience.

I think your best bet for speed readout is the one posted earlier. After your itch is scratched, you'll no longer care about it.

Say, don't you love your torque now?? And, I hope you put in a reversing switch while you were at it. ;>} Ed

Re: VS mini lathe - shopmade version

#8

Re: VS mini lathe - shopmade version

Carol - now in NC Nebraska

>Thanks, Ed,

I don't have it done yet. I am renewing all my gathered information and making a shopping list. I need switches, air filter material, fan guard, plywood, etc.

Would you mind looking at my wiring diagram and second guess me as to correctness? Right now it is a cad file, but I could make it a jpeg. I could email it to you. That would be most helpful. And you sound like you have already done this. If you have, I would love to see pictures. hint, hint!

My biggest concern is the reversing wirings. On the non-shaft end of the motor there is a yellow and black wire that appear to coming from the motor windings. They are connected to the armature with spade connectors. I am assuming they are the ones that need to reverse.

I have two of these motors. The lady who fixed the boards for me said they are very fragile, so for general messing around I am carefully bringing leads out to screw terminal blocks.

The second set up is for a shop made horizontal powered Scary Sharp system I put together several years ago. I need the reversing feature there also.

Everyone is right about the tachometer, but the cool factor is enticing. I actually have found a couple of ways to do it. Just depends on how much trouble I want to go to and how much money I want to spend. The answer is 'not much.' LOL

Re: VS mini lathe - shopmade version

#9

Other Thoughts

Clem Wixted

>Carol,

I don't know much about digital readouts but many treadmills have a readout for the speed that you are walking on the mill. This circuit is keyed by a magnet somewhere on the treadmill and a pickup that reads that magnet on every revolution. You might be able to connect one of those readouts and get a relative reading, or if you can adjust the circuit have it read rpm's.

I have a Vega motor and board that I have yet to install and 3 or 4 treadmills that I have salvaged the motors and other electronics from. I hope to do the same as you, someday.

Another thought is to use one of those bicycle speedometers. It wouldn't read rpm's but an mph readout might be "cool"

Clem

Re: VS mini lathe - shopmade version

#10

Re: Other Thoughts

Carol - now in NC Nebraska

>Ah, Clem, you have found my secret!

I picked up a treadmill for the motor and stuff at a local (Arizona) thrift store for 5 bucks. It has the magnetic tach sensor. The circuit board however, is another matter. And it is in Arizona and I am currently in Nebraska! But a motor and lots of other goodies for $5 is a steal no matter what. I have a drum sander on the drawing board and a lot of the parts are going to go into that someday.

As for this project, I've got something else cooking. Let you all know if it works out.

BTW, I am taking pictures as I go, so when you get around to it, I may be able to help, as Mark Kauder's article and emails are helping me, along with other folks here and there who are patient enough to answer my questions.

As I said, the tach is just a cool factor. The big boy lathes have them, and since everyone seems to think they are redundant to experience, they must just be there for the sake of coolness! :)

The wind in howling here and the chill factor is in sub-zero digits. I preferred it when 'sub-zero' was only the brand name of a rather expensive refrigerator! So I am amusing myself by tricking out my mini lathe - at the computer. I ordered a bunch of things (switches, fans, etc.) last night, so perhaps later on I will actually get to the tricking part.

Hey, they do it to trucks on TV!

On the other hand, boxes keep arriving, heavy enough to have wood in them, but with instructions to not open until Christmas. I am impatiently waiting, but with great delight, as some of you folks are proving to be very generous!

Pictures on Tuesday.

Re: VS mini lathe - shopmade version

#11

Re: VS mini lathe - shopmade version

Ed Heuslein

>Howdy Carol: I'd be happy to help any way I can. Send me what you have, but keep the size under 1MB if you can as I have one of those old dial-up systems. I suggest a PM to keep this thread from getting out of hand. MY email address is heuslein@earthlink.net. I'll take a couple pictures of what I have tomorrow and send what I have to you. My diagrams are not very good, but I'll do what I can to help - even snail mail if necessary.

Re: VS mini lathe - shopmade version

#12

Re: VS mini lathe - shopmade version

Carol - now in NC Nebraska

>Thanks, Ed.

PM on the way after I finish reading the posts.

Carol