Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

broken pulley

Posts

broken pulley

#1

broken pulley

Jim Jacomb

>I have a rockwell 46-111 I bought used 30+ yrs ago. No manual, anyway the lathe has a four stepped pulley on the headstock and the motor. Well, the smallest sheave on the motor group broke. I'm afraid to check prices through local dealers. Any suggestions? thanks

Re: broken pulley

#2

Re: broken pulley

Allen Neighbors

>I have no idea, except for a little place called Luke's Salvage, here in my home town. What size shaft is the motor, and is it a Vee belt, or one of those with a lot of grooves? What is the outer diameter of the large pulley, and the smallest, and the width of the grooves? I might find one for it here.

I know this doesn't solve your problem, but how often do you use that high speed?

Re: broken pulley

#3

Re: broken pulley

Jim Jacomb

>The bore is 5/8" smallest is 2 1/2" largest is 4 1/2" V groove, A size. I never run the largest, and wish I could slow down even more when turning large chunks. I've thought about building an intermediate shaft system to help slow things down. The price of a variable speed conversion seems too high for my budget.

Re: broken pulley

#4

Re: broken pulley

Jerry from Lapel In.

>Try this link. http://stores.ebay.com/ElectricMotorSite_Fixed-Bore-Pulleys_W0QQcolZ2QQdirZQ2d1QQfsubZ9QQftidZ2QQtZkm

Re: broken pulley

#5

Re: broken pulley *LINK*

Mike Cunningham (Cape May NJ)

>Jim,

A year or so back I was in need of one for a Rockwell/Delta and found a dealer of old Rockwell/Delta parts through the Old Woodworking Machines website. I can't recall the dealer's name but if you go to the link and look around for old Delta parts or post asking for a source you'll find it. I can tell you that OEM pulley is around $90. You can also try Emco and Surplus supply for similar but not exactly the same pulleys.

Mike


OWWM

Re: broken pulley

#6

Re: broken pulley

Robert Henderson

>Try McMaster-Carr at mcmaster.com

Re: broken pulley

#7

Re: broken pulley

Larry in NW Ohio

>Would you have a web address for this Emco surplus. Thank you Larry in Ohio

Re: broken pulley

#8

Re: broken pulley

Lan Brady

>Jim,

Most pulleys are cast metals. I bought a machined steel pulley for my table saw and could not believe the difference it made.

I bought it from the Dubby Sled man, so I do not know where to buy them. The differnece is worth it.

Lan

Re: broken pulley

#9

Re: broken pulley

Allen Neighbors

>Jim, soon as I finish lunch, I'll run down to Luke's and see if he has one. I'll let you know if I find it.

Re: broken pulley

#10

Re: broken pulley

Doug Turner

>Turn a wood pulley. I had an old 1920's Oliver with an original wood pulley that was turning a 2" shaft. Use a coarse threaded set screw to attach to the shaft.

Re: broken pulley

#11

Re: What HP is your Motor?

Allen Neighbors

>Is your motor 1/2 HP?? There is a 1/2 hp Variable Speed system in Penn State's catalog for about $100, including the motor. It could be easily adapted for almost any Mini Lathe. Don't know what yours is, so just thought I'd mention it.

Re: broken pulley

#12

Re: Good idea, Doug...

Allen Neighbors

>I never thought of turning a wooden pulley, before. But Bois d'Arc or Lignum Vitae would both be good wood for a wooden pulley. I'll just keep this on my 'possibilities' list. Thanks for the idea.

Re: broken pulley

#13

Re: broken pulley

Pete in Holland, MI

>Look up in the yellow pages for "power transmission equipment". A 5/8" bore step pulley shouldn't be that difficult to find.

You could also buy 3-4 individul hub-less pulleys and create your own unit by assembling them side by side on the spindle.

Flat belt pulleys can be turned from wood, but v-belt pulleys should be avoided, as the thin wall of the pulley won't have much strength.

Re: broken pulley

#14

Re: broken pulley *LINK*

Mike Cunningham (Cape May NJ)

>Surplus Center is:

http://www.surpluscenter.com/home.asp?UID=2007121414252716

Enco is at the below link

Mike


ENCO

Re: broken pulley

#15

Steven Antonucci

Glue it

steve antonucci

>I had a broken cast iron part on my bandsaw, so I decided to glue it with CA. Not only did it hold for a very long time (it's still holding), but it worked so well that when the replacement came, it took me another month to swap it in.

Can't hurt to try

Steve