Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Shop flooring question

Posts

Shop flooring question

#1

Shop flooring question

Carole Valentine

>I am too old to keep working on a concrete slab and want a wood floor in my new shop. Right now it calls for two layers of 5/8" ply with the top layer laid opposite and overlapping the layer below. Not sure what the joist setup is but I will ask. I am a little concerned about vibration though my builder assures me it will be rock solid. He has build numerous shops including his own and he has some huge industrial equipment in there that weighs far more than any lathe I would ever own, BUT he does not have a lathe in there. I know that a lathe can cause unique vibrations. Has anyone done a floor like this and did you have any problems? I was wondering about some sort of damper sheet between the floor layers and if such a thing exists. Am I just a worry wort?

Re: Shop flooring question

#2

Re: Shop flooring question

Keith Inscho E. Tenn.

>Carole, This type of floor is fine for just about anything as long as the joists are either beefy enough (2"x12") or close enough together (12" centers). If the lathe will be placed close to an outside wall you should have no problems but if you want the lathe out in the middle of the floor you might want to consider an extra support piller/beam directly under the lathe location. My $.02

Re: Shop flooring question

#3

Re: Shop flooring question

Ron in Drums PA

>Hi Carole

In my print shop I have a 2300lb printing press sitting on a wood floor. In the basement directly under the press I set up a pair of lolly columns to support a 4x6 header. This setup has worked for 12+ years

I found this image on google and it is exactly how mine is set up. Also, notice that the floor joists are doubled.


Re: Shop flooring question

#4

carl

Re: Shop flooring question

Carl

>Hi,There would be more vibation on a concrete floor,your fine,,Carl

Re: Shop flooring question

#5

Re: Shop flooring question

Barry Elder

>Keep in mind that any vibration in the flooring means you need to work on your lathe or the wood you have mounted in it. If you get any real vibration in your floor, there probably has been some action in the New Madrid fault!!! Har! Har! Hope you never see that!

Re: Shop flooring question

#6

Carole: A question...

david

>The structure for the floor does not appear to be a problem, but am interested in what you are considering for the floor finish. Sheet vinyl? Vinyl composition tile? Wood flooring? How about some cork flooring?

Re: Shop flooring question

#7

What I did in my shop.

Brian Hahn in SW Wisconsin

>My shop has engineered joists 16" on center with a beam running down the center. The joists were spec'd for standard construction and are more than adequate for shop use. Consider that a cabinet saw weighs less than a football player and my new lathe is a several defensive ends.

The sub-flooring is 3/4" tongue and groove OSB - standard construction practice. I put 3/4" underlayment plywood (BC grade) on top of that, all joints offset, glued to the OSB with beads of yellow glue and nailed to the joists. The carpenter remarked at how stiff the floor was with this treatment. I finished the plywood with multiple coats of a tung oil based flooring varnish.

The only problem I have with vibration is with heavy out of round pieces on the lathe. The lathe is about 4' from the central beam and 9 feet from the foundation wall. My solution is two lolly columns and a beam under the long joist section by the lathe so the floor has beams on either side of the lathe.

A wood floor is wonderful. Your body and your tools will thank you!

Re: Shop flooring question

#8

Along the same lines...question

Steven Kubien

>Let's say I cannot put a full wood floor in my shop (single car garage/shop/studio). Does anyone see any harm in building a platform/deck for my lathe area? I am thinking 6'x6' or 6'x8' (my lathe is a Nova 1624 with no bed extension).

Thanks,

Steve Kubien

Ajax, Ontario, where the concrete gets mighty cold this time of year.

Re: Shop flooring question

#9

Re: Along the same lines...question

Peter Hyde

>Steve, if there is no car use I would do the whole floor. I live in Niagara and the cold concrete floor is a real pain in the winter. I was lucky to get my hands on a floor from a theatre set for free. It is 3/4 Exterior ply with a layer of 1/4" felt covered with 1/4" tempered masonite. I used a slotting bit in the router and put a 3/16" groove in all edges of the ply sheets. Then I covered the whole concrete floor with 6mil poly as a moisture barrier and loose laid the sheets using plywood 3/16 tongues glued into the grooves to keep all the edges flush. Around the perimeter I left a 1/4" gap and brought the poly up the walls about 6". When the whole floor was laid I went around the gap with a silicone caulk and later trimmed off the excess poly. The floor is totally floating with no fixings into the concrete at all. It's now into it's third winter and no problems so far apart from being slippery with certain shoes on. I notice a big difference in heating costs as well as the foot comfort.

Re: Shop flooring question

#10

That's what my Dad did.

Brian Hahn in SW Wisconsin

>He build several platforms for the areas he normally worked. They were real simple, just some boards nailed to some 2x2's. He left a gap between the boards so debris could fall through, which helped to insulate the concrete floor below. It made his shop a lot more comfortable in the winter.

Re: Shop flooring question

#11

Plywood floor

Stuart Johnson

>A couple years ago one of the woodworking magazines had an article about adding a wood floor. They laid 2x4's flat (I think glued down) and then covered it with 3/4" plywood. It gave a good solid floor without raising it that much.

Re: Shop flooring question

#12

Re: Shop flooring question

gtw

>Carole,

To stop vibrations I use strips from a rubber conveyor belt under the lathe however I am on concrete and use the same conveyor belt for a mat.

Last year I found heated rubber floor mats mats at www.floormats.com which is Martinson-Nicholls Inc. they have a grey anti-fatigue mat which I think is the best thing since sliced bread.

Trevor

Re: Shop flooring question

#13

Re: Shop flooring question

Barbara Gill, Remlik VA

>When we install flooring over plywood, we use a layer of roofing felt to prevent squeaks. I have never installed a double layer of plywood but would think that the layers will work against each other ans squeak if no felt has been used.

Re: Shop flooring question

#14

Re: Shop flooring question

keith zimmerman, Normal IL

>Wood all the way! I would use 2x stock as sleepers, 12" on center to apply your subfloor to. Then, another layer of 3/4" plywood laid perpendicular as the floor. I would use plywood rather than OSB because plywood will wear better.

In days of yore, when I had a conventional shop, it was freestanding. I built it like a deck, with the posts anchored in the ground 40". On the ground I laid out 6mil plastic sheet covered with white rock to prevent weed growth. I attached the joists 12" on center to the rim joists. On top of that I laid 32 12' 2x12s, side-by-side. I made an amazing deal of these 2x12s at a lumberyard going-out-of business auction and I had not other use for them. I then laid 3/4" CDX plywood on top for the floor surface. 2 coats of floor enamel and I had a solid wood floor with no vibration whatsoever. It was one step up to get into the shop.

Good luck with your floor Carole.

keithz

Re: Shop flooring question

#15

Thanks everyone

Steven Kubien

>

Re: Shop flooring question

#16

Re: Shop flooring question

Pete in Holland

>If the problem is standing on concrete floors, how bout anti-fatigue mats where you do most of your standing? Insulates your feet from the cold concrete too.

Re: Shop flooring question

#17

Re: Shop flooring question

robo hippy

>As some one who poured concrete for 30 years, I would want any area that I was standing on a lot covered. That concrete is just too darned hard. Anti fatigue matts will work well. Wood works well also. You don't really need to build up a platform of 2x2 or 2x4. You do need a vapor barrior like tar paper, or even 6 mil plastic. In cold areas, you should insulate the floor and stem walls. One layer of 3/4 inch ply would work fine. You could get fancy and put in a wood floor, of hickory or oak.

robo hippy

Re: Shop flooring question

#18

Thanks folks

Carole Valentine

>You have given me some things to think about. The only thing I am completely sure of is that I don't want concrete. I have anti-fatigue mats and heated mats my current shop. Yes they help a lot, but it's not like wood! The floor will be insulated from the crawl space, but I will also look into a layer of felt between the two layers.