Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

workshop heating

Posts

Re: workshop heating

#26

Re: workshop heating

john lucas

>Ken Your just plain mean. However after I win the lottery tonight I'll be in Tahiti or Hawaii or somewhere really temperate and it won't be problem anymore.

Re: workshop heating

#27

Hey Ruth

Ron in Drums PA

>Do you have any problem with your finishes drying overnight with the temps down to 45-50

Re: workshop heating

#28

Now You Got Me Thinking!

George Van

>

Re: workshop heating

#29

Re: workshop heating

Texian

>John,

Get that 220 line run ASAP. Install maximum insulation if none present. My 25x30 shop has "window unit" in purpose built opening, elevated, center of back/long wall. Been leaving heat set at 68 at night to keep wood, finish work in progress warm. When ambient outdoor reaches about 60, the lights are enough to maintain 70 in the shop. In warm weather the A/C mode was set to 72 or even 70 to help keep humidity down. This is first winter for this shop and min. temp so far only about 40. Expect lows to around 28, highs next summer to 100+. My fourth shop with this type heat/A/C. Considered propane heat for this and previous shop (the houses had/have propane heat), but still need A/C. Much simpler just to stick one unit in the wall that does both. Gets colder longer where you are, so heating cost is a concern. Minimal impact on electric bill here (or so I tell my sweetie). We used to heat one of the greenhouses (1,000 sq. ft.) at previous location with kero, and just to keep it above freezing was costing about $6 a night.

Re: workshop heating

#30

Re: workshop heating

Ed Karch

>14'X22' with cathedrial celing and loft. Concrete slab with insulation and wood false floor over it. Walls with 2x6 studs insulated and house wrapped with vinal siding. Heated with natural gas. As the price of NG goes up so do the royalties on my Oklahoma gas wells. Temp is a constant 65.

Re: workshop heating

#31

Re: Hey Ruth

Ruth Niles

>Ron, I don't use a lot of finish, mostly I just use Walnut, or other natural oil, and buff. If I do want to put a finish that needs drying, I'll take it in the house. Learned not to leave it in the shop, not a lot of fun lesson! : )

Re: workshop heating

#32

Re: workshop heating

Barry Turner

>I use a 4800-watt milkhouse heater. It has a clothes dryer-type plug on the end. It's about 35+ years old. The only problem, the sanding dust eventually gets into the squirrel-cage motor and stops the fan. With no air blowing across them, the coils quickly turn red-hot and the thermal overload protection turns the heater off. Then, I have to stop turning and disassemble the heater, clean out the dust, and reassemble. It takes about 30 minutes, with practice and using a cordless driver/drill on the screws. Now, that I am turning, I have less sanding dust, than with flat-work. But I still have to clean the heater once a year or so. It heats my shop just fine, (it's 24' X 24', too) until the temp drops below 20-degrees or so. When that happens I go to the house and watch DVD's on woodturning. I haven't tried to calculate the cost of running the heater for 8 hours, but I suspect it exceeds the income I can generate in the shop in 8 hours.

Re: workshop heating

#33

Re: workshop heating

Barry Turner

>.......my shop is stud wall construction, concrete floor. Walls and ceiling are insulated. I have an 18' overhead door on one side that I am sure is leaking all sorts of heat..........

Re: workshop heating

#34

How about a different approach?

Barry Irby

>Get one of those Thermal Wraps meant for a back ache and some of the toe heaters. They claim they provide warmth and relief for eight hours. Buy them buy the case and put them on every time you have a day in the shop. Wonder what they cost?

Re: workshop heating

#35

Re: How about a different approach?

john lucas

>Barry I tried thermal socks last year but the heating element was right under the joint in my toes and it hurt to stand on it. It would work great if I was just sitting.

Re: workshop heating

#36

Best solution yet!!(??)

Mike Jones

>http://www.matsmatsmats.com/commercial-industrial/HEATED/heated-foot-warmer-mat.html?Source=GOOGLEAW&gclid=COCpvrGm548CFQwfYAodFSSkjg

Re: workshop heating

#37

Re: workshop heating

Pete in Holland

>Solutions:

1) Reduce the area you are trying to heat.

2) Insulate

3) Fan to get the heat from the ceiling down to you.

4) Move you lathe to an inside shop (mine's in my basement).

5) For infrequent heat needs, radiant is much better than convection. Heats the objects around you and not the air.

6) Find another hobby for the winter that keeps you indoors.

7) Most all ideas to save you heat dollars will cost you up front. Are you willing to spend a few thousand dollars to reduce your heat bill from $18 to $12 for 3 days of shop time? Might be cheaper for many years to simply buy the kerosene. Do some math.

If it's pure comfort you want, break out the check book and go shopping at the local big box board store ! : )

Re: workshop heating

#38

Re: workshop heating

eaglesc

>Make or ask your local HVAC guy to make a sheet metal box that will accept a standard filter.

Set the heater in the open end so the air that supplies the milkhouse hearter gets filtered.