Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Turning Handles

Posts

Turning Handles

#1

Turning Handles

keith zimmerman, Normal IL

>I need to turn some handles for tools and having never done so, I realized that I have no idea what wood to use. Any suggestions?

keithz

Re: Turning Handles

#2

Re: Turning Handles

Bill Howatt

>Anything you want. I have seen very pretty ones turned from exotic wood like cocobolo. I have made them from maple, dogwood and pine.

You can buy ferrules or use pieces of copper pipe, copper pipe straight couplers usually cut in half since they are rather long, brass fittings, etc.

The tool can be just jammed into the hole or glued with CA, polyurethane glue or epoxy if desired.

Bill

Re: Turning Handles

#3

Check out Alan Lacer's article *LINK*

Brian Hahn in SW Wisconsin

>Several years ago Alan Lacer had a good article in American Woodturner. The article is on his website at the link below. Click on articles and it is at the bottom of the list.

My all time favorite handle wood is hickory.

Also, this topic has come up several times recently. A search for "tool handles" should get you plenty of information and links to several other articles.


Alan Lacer Woodturning

Re: Turning Handles

#4

Re: Turning Handles

Doug Thompson near Cleveland

>Free wood works best!

Re: Turning Handles

#5

Re: Bois d'Arc/Oak/Pecan, too.

Allen Neighbors

>

Re: Turning Handles

#6

Re: Turning Handles *LINK*

Gordon Seto

>Here is a very informative article. It covers using various materials to make ferrule and fitting a flat tang.

Gordon


Tool handle instruction

Re: Turning Handles

#7

Re: Turning Handles

Steven Kubien

>Hi Keith,

I've made my handles from a bunch of different woods based on what was lying around at the time. Maple, dogwood, hickory, mahogany (salvaged from a pallet if you can believe it!). I like the hickory the best because even when sanded to 320 it still has a bit of 'grippiness' to it. BLO and some wax is the finish on all of them and I think, as has been mentioned, I epoxied the tool into place and used copper pipe ferrules.

Hope this helps,

Steve Kubien

Ajax, Ontario

Re: Turning Handles

#8

old oars

tek-Brunswick, Ohio

>How is this for free dry wood.I was looking for some wood to make handles for some of my Thomson tools. I found some old oars stored up on the ceiling joists of my mother in law's garage. They have to be at least 40 yrs old and the blades were shot. The row boat has been gone at least 30 years. They looked and smelled like elm when I turned them. I didn't know they made oars from elm. I base the shapes of my handles on my Crown Tool handles because those handles are comfortable for me. I use straight couplers for 3/4" copper pipe, for ferrules. I cut them in half and get two ferrules from each one.

Re: Turning Handles

#9

bed and chairs in the dump

john lucas

>OK I'll admit it. I'm a dumpster diver. When I'm driving along the road and see a chair or bed or table in the garbage I dive in. The legs are often in good shape and really dry. They are great for tool handles.

Re: Turning Handles

#10

Ebony Handles for Thompson Tools!

Jennifer@Indy.USA

>Doug I saw a set of 5 Thompson tools today with the most amazing ebony handles and brass ferules. They were gorgeous and fit like a glove. Jim Dupler made them for Don Skiles here in Indy and they are stunning. I wish someone could get you a really nice photograph of them all together. You should have a shot of these for your site. Now that I think about it...we should have had Jamie Donaldson take a photo of them! He was doing a Frugal Photography demo here at our club today. Doh! That was really dumb of me not to mention it to him. Ugh. If you can get in touch with Jim Dupler perhaps he can get you a photo of them.

Re: Turning Handles

#11

Re: Ebony Handles for Thompson Tools!

Doug Thompson near Cleveland

>Jim, Ebony handles what a outstanding gift. You should post a picture here and send a copy. They sure do good in black.

Re: Turning Handles

#12

Name Dropping...

david

>Whatever kind of woods you use: Allan Batty was at my shop yesterday conducting a hands-on workshop, and he said that the handle should not be so large that when grasping it, you cannot touch the ball of your hand with your fingers.

Re: Turning Handles

#13

Re:Any time I hear about fancy wood....

JamieD

>... tool handles I think of Rude Osolnik. He had the most ugly collection of nasty tool handles you could even envision, often changing the steels in a handle in mid-task and whacking in a different tool by hitting the butt of the handle on the bedway. Several of his fans made beautiful handles for him over the years, including myself, and they always seemed to soon disappear in his shop. I'm very sure that most of them were transformed into candlesticks when we weren't looking!

Re: Turning Handles

#14

Re: Ebony Handles for Thompson Tools!

john lucas

>The handles cost more than the tools. I'll bet they look fantastic.

Re: Turning Handles

#15

Re: Turning Handles

eliot d

>You certainly have enough suggestion here. Here's a neat tip: when you are fitting the ferrule, turn the tenon so the diameter is just a hair too large to fit in the copper tube, or whatever. Then heat the ferrule with a blow touch for a moment so it expands over the tenon. When the ferrule shrinks back , it will never come off.