Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Question about power sanding

Posts

Re: Question about power sanding

#27

Re: shop made inertia sander

eliot d

>Very elegant. The one I made is nothing more that a turned handle with a hole in it; but it works just fine.

Re: Question about power sanding

#28

Cheap 'n Ugly Alternative

Rick Urban

>Here's a piece of closet rod dowel with a hole in the end and one in the side at a 45 degree angle to receive one of my H&L mandrels. There's a tiny screw in the bottom to act as a bearing. The black "tape" is self stick hook fabric. I use smaller dowels (and credit cards) with PSA/hook fabric as "handles."

They're not pretty enough to be rated as "not-even-close" to the other elegant solutions, but they cost about $0.75 and work well enough I haven't had the urge to make an upgrade.

Re: Question about power sanding

#29

Re: Cheap 'n Ugly Alternative

Carol Reed - in Nebraska

>Missed the picture. :)

Also what is the source of your H&L mandrels?

Re: Question about power sanding

#30

Missing Picture

Rick Urban

>I gotta figure this stuff out sometime... thought it previewed ok.

Re: Question about power sanding

#31

H&L Abrasives

Rick Urban

>I get most of my H&L from Industrial Abrasives, Reading, PA. I buy in quantity to reduce my costs and resell some to fellow turners to give them a break too. I'd rather be turning wood, so I haven't tried to make that a line of business. I get my H&L interface pads from them only to avoid having to deal with multiple suppliers and multiple shipping charges. They are cheaper several other places.

Re: Question about power sanding

#32

Trying again...

Rick Urban

>Let's see if it works this time...


img

Re: Question about power sanding

#33

Disk Sander Adhesive works really well, too

Rick Urban

>

Re: Question about power sanding

#34

Re: Trying again...

eliot d

>I guess I don't follow you about credit cards. What do these have to do with making an inertia sander?

Re: Question about power sanding

#35

Re: Allen Neighbors sanders

Allen Neighbors

>Carol, I used all thread because I had it. I also think the threads give more purchase for the epoxy.

I buy used rollerblades at thrift stores... usually for about $3 a pair. A skating rink usually has a bunch of them in the trash, but those may be very well worn.

I buy those flip-flops at large Wal-Mart stores - about this time of year they have them on sale for $1 a pair. I buy the largest ones I can find, and try to get some with hard (1/8") soles and some with soft soles. The harder (more un-flexible ones) are best for surfaces which are not too curvy... softer soles work well on the curviest surfaces because they are so flexible.

When I make my next ones, before I put the flip-flops on the wheels, I'll hold the wheels at a slant on a 50 or 60 grit belt sander, and reduce them to about 2" diameter. Then I'll cut the flip-flop to 3" dia, and it'll flex even more.

They really work well.

Re: Question about power sanding

#36

Re: Goop and DSA... sounds OK 2 me

Allen Neighbors

>

Re: Question about power sanding

#37

Re: Allen Neighbors sanders

Carol Reed - in Nebraska

>Thank's Allen. I have added this to my stash of info and will be in the hunt for wheels and flipflops.

Thanks so much.

Re: Question about power sanding

#38

Credit Card H&L Handles

Rick Urban

>The shaft of my "poor boy" inertial sander has self stick (PSA) H&L hook material on it for those instances where I cannot insert the tool with a H&L mandrel. I slap on the H&L disk (or piece cut from the sheet material) and sand away. As an extention to that though I also put the self stick (PSA) H&L hook material on old credit cards and they make an instant "handle" when I need to work without the mandrel in other tight places, e.g. detail areas or a bit of hand sanding in a particularly gnarly spot.

Some don't like to use the H&L for hand sanding, but I appreciate the ease and convenience.

Re: Question about power sanding

#39

Re: Credit Card H&L Handles

eliot d

>Nifty idea; I wouldn't have thought of it.